Scag Power Equipment SFW36-16BV manual Limited Warranty SFW, Inside Back Cover

Page 4

R

Table of Contents

SECTION 6 - ADJUSTMENTS	19
6.1 DRIVE CONTROL ADJUSTMENTS	19
6.2 Throttle Control and Choke Adjustments	19
6.3 BELT ADJUSTMENT	19
6.4 BELT ALIGNMENT	19
6.5 CUTTER DECK ADJUSTMENTS	19
6.6 electric clutch adjustment	20
SECTION 7 - MAINTENANCE	22
7.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS	22
7.2 Lubrication	23
7.3 Engine Oil	24
7.4 Engine Fuel System	24
7.5 Engine Air Cleaner	25
7.6 DRIVE BELTS	25
7.7 CUTTER BLADES	25
7.8 TIRES	26
SECTION 8 - ILLUSTRATED PARTS LIST	27
8.1 SCAG APPROVED ATTACHMENTS AND ACCESSORIES	27
36" CUTTER DECK	28
48" CUTTER DECK	30
CUTTER DECK CONTROLS	32
HANDLE ASSEMBLY	34
ENGINE DECK	36
ELECTRICAL SYSTEM AND THROTTLE CONTROL	38
REPLACEMENT DECALS AND INFORMATION PLATES	40
SFW ELECTRICAL SCHEMATIC	42
LIMITED WARRANTY - SFW	Inside Back Cover

II

Image 4

Contents

OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Always Follow Osha Approved OperationTable of Contents Limited Warranty SFW Inside Back CoverGeneral Information IntroductionDirection Reference Servicing The Engine And Drive Train ComponentsSymbols STT ModelsSafety Information Signal WordsThis symbol means Attention! Become Alert! Your Signal WordOperation Considerations Maintenance Considerations & storage Using a spark arrestor Safety and Instructional Decals Install Belt COvER BeforeFalling HAzARD USE only Scag APPROvED Riding AttachmentsSpecifications EngineElectrical Engine DeckWeights and Dimensions ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresStarting the Engine First Day of Use or Approximately 20 HoursForward Travel Ground Travel and SteeringReverse Travel Engaging the Deck Drive Cutter Hillside Operation Blades Parking the MowerRotating Blades After OperationRemoving Clogged Material Moving Mower with Engine StoppedAdjusting Cutting Height Cutting HeightTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Dirt or CuttingVery Close To the GroundStep Cut Ridge in Center Cutting pathAdjustments Drive Control AdjustmentsBelt Adjustment Cutter Deck AdjustmentsElectric clutch adjustment Cutter Deck PitchIf the air gap is too narrow, the clutch armature may drag Maintenance Chart Recommended Service Intervals MaintenanceProcedure Comments Break-In 100 200 500 First Maintenance Chart Recommended Service Intervals Contd LubricationEngine Oil Engine Fuel SystemDrive Belts Engine Air CleanerCutter Blades Tires Blade ReplacementBlade Sharpening Illustrated Parts List Scag Approved Attachments and AccessoriesCutter Deck 462150 Cutter Deck Weldment w/Decals 14 20 1217 462149 Cutter Deck Weldment w/Decals Cutter Deck Controls Cutter Deck Controls Handle Assembly Pulley, Jackshaft 3.25 OD x .625 Bore Engine Deck Description Electrical System and Throttle Control Ref. No Description Replacement Decals and Information Plates Spinning BladesRotating Blades and Belts Do not Operate Unless Grass CATCHER, Mulching kIT or1 2 3 SFW Electrical Schematic Limited Warranty SFW

Related manuals

Manual 18 pages 62.01 Kb