Scag Power Equipment GC-STT manual Back Side Idler Pulley Blower Pulley Front Side Spindle

Page 10

6.Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001- 71), 1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). See Figure 4-3, Page 7. Do not fully tighten the hardware at this time.

7.Install the catch plate (p/n 423297) to the blower assembly using 3/8-16 x 1-1/4" carriage bolts (p/n 04003-11) facing upward. See Figure 4-4, Page 7. Secure with 3/8" spring lockwashers (p/n 04030-04) and 3/8-16 elastic stop nuts (p/n 04021-09). Do not fully tighten the hardware.

8.Install the blower assembly to the mounting bracket and secure with the mounting pin. See Figure 4-4, Page 7.

9.Align the blower assembly with the discharge opening of the cutter deck. Tighten the hardware for the mounting bracket. Then tighten the hardware for the catch plate.

10.Install the belt to the spindle pulley. When replacing the belt, see figure below.

13.Install the hopper hood assembly onto the catcher frame assembly and secure with 3/8-16 x 2-1/4" hex head bolts (p/n 04001-46) and 3/8-16 elastic stop nuts (p/n 04021-09) See Figure 5-6, Page 13.

14.Install the catcher support bracket onto the rear of the machine and secure with 5/16-18 x 1" carriage bolts (p/n 04003-04) and 5/16-18 serrated flange nuts (p/n 04019-03).

See Figure 4-5.

Catcher Support Bracket

BACK SIDE

IDLER PULLEY BLOWER PULLEY

FIGURE 4-5

FRONT SIDE

SPINDLE

PULLEY

IDLER PULLEY

 

11.Install the new belt covers and secure with the plastic wing nuts. See Page 18 of the Illustrated Parts List for proper installation.

12.Install the hopper mounting brackets

(p/n 451512) to the outside of the frame on the rear of the machine using 3/8-16 x 1" hex head bolts (p/n 04001-19) and 3/8-16 elastic stop nuts (p/n 04021-09). See Figure 5-6, Page 13.

15.Install the heat shield to the hopper hood assembly and catcher frame assembly. Secure using the hardware specified in Figure 5-6, Page 13.

16.Install the catcher frame assembly onto the rear of the machine and secure with the quick pins (p/n 04066-03) See Figure 5-6, Page 13.

17.Install adapter (p/n 461419) to the blower assembly and secure with the strap.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Introduction Safety and Operating InstructionsDirection Reference Assembly Instructions for 52 Cutter Decks Right Side Cutter Deck Shown Back Side Idler Pulley Blower Front Side Spindle Operate and test Assembly Instructions for 61 Cutter Decks Rear Cutter Deck Discharge Chute Opening Back Side Idler Pulley Blower Pulley Front Side Spindle Assembly Instructions for 72 Cutter Decks WeightBack Side Idler Pulley Blower Right Side Cutter Deck Shown Catcher Support Bracket Liquid Cooled Only Grass Catcher Removal Instructions Clevis PINPage 16 15 GC-STT Blower Housing Assembly GC-STT Blower Mounting Components Part Number Description GC-STT Bucket Support Components Some of the hardware is common hardware GC-STT BAG Support Bracket and Seal 423198 GC-STT Decals Page Limited WARRANTY- Commercial Accessory Scag Power Equipment
Top Page Image Contents