Scag Power Equipment SZC manual Starting the Engine, Ground Travel and Steering, Forward Travel

Page 18

Section 4

4.3INITIAL RUN-IN PROCEDURES (First Day of Use or Approximately 10 Hours)

1.Check all belts for proper alignment and wear at 2, 4 and 8 hours.

2.Change the engine oil and oil filter after the first 8 hours of operation. (See Section 7.4.)

3.Check hydraulic oil level in reservoir. (See Section 7.3)

4.Check for loose hardware. Tighten as needed.

5.Check interlock system for proper operation. (See Section 4.2)

6.Check tire pressure. Adjust pressure if necessary. (See Section 7.10)

4.4 STARTING THE ENGINE

CAUTION:

DO NOT USE STARTING FLUIDS. Use of starting fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition that could result in engine damage and/or personal injury.

1.Be sure the fuel shutoff valve, located behind the operator's seat by the left fuel tank, is completely open. (See Section 7.5)

2.Sit in the operator’s seat, fasten seat belt and place the steering control levers in the neutral position.

3.Engage the parking brake.

4.If the engine is cold, choke the engine as needed.

5.Move the engine throttle control to about half engine speed.

6.Turn the ignition key to the START position and release the key as soon as the engine starts. Do not hold the key in the START position for more than 15 seconds at a time. Allow at least 60 seconds between each cranking attempt to prevent overheating of the starter motor. Prolonged cranking can damage the starter motor and shorten battery life.

7.Allow engine to warm before operating the mower.

4.5 GROUND TRAVEL AND STEERING

-IMPORTANT-

If you are not familiar with the operation of a machine with lever steering and/or hydrostatic transmissions, the steering and ground speed operations should be learned and practiced in an open area, away from buildings, fences, or obstructions. Practice until you are comfortable with the handling of the machine before attempting to mow. Learn the operation on flat ground before operating on slopes.

-IMPORTANT-

Start practicing with a slow engine speed and slow forward travel. Learn to feather the steering controls to obtain a smooth operating action.

Forward Travel

To travel forward with the mower, disengage the parking brake, pull levers inward out of the neutral lock position and slowly push the steering control levers forward an equal distance. The further the steering control levers are pushed forward the greater the forward speed will be. To increase the speed, push the steering control levers further forward and to decrease the speed, pull the steering control levers back.

To stop the forward travel, pull the steering control levers back to the neutral position.

To steer the mower left while traveling forward, pull the left steering lever back. The further the lever is pulled back, the quicker the mower will turn left.

14

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Direction Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Safety Information Signal WordsBefore Operation Considerations Before Operation Considerations Contd Operation ConsiderationsOperation Considerations Contd Roll Over Protection SystemSeat Belt Inspection Maintenance Considerations & Storage SZC With Optional Roll Over Protection SystemSafety and Instructional Decals Electrical SpecificationsEngine TractorHydraulic System Tractor ContdCutter Deck ProductivityStart Safety Interlock System Dump Valve ControlStarting the Engine Ground Travel and SteeringForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Parking the MowerMoving Mower with Engine Stopped Adjusting Cutting HeightRemoving Clogged Material Recommendations for MowingDeck Release Lever Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentBelt Adjustment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AlignmentCutter Deck Adjustments Cutter Deck LevelCutter Deck Pitch Custom-Cut Baffle Adjustment Cutter Deck HeightCustom-Cut Baffle Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine OIL Engine Fuel SystemEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner ElementBattery Charging the Battery Jump StartingCutter Blades Blade ReplacementDrive Belts Blade InspectionTires BODY, DECK, and UpholsterySection 36A& 42A Cutter Decks Part Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Sheet Metal Components SZC Roll Over Protection System Ref. Part No. No. Description Drive System Components Drive System Components Engine and Attaching Parts Part Description To Pump Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Heavy-Duty Commercial 482166R SZC 2005 RDP2 Electrical Schematic Kawasaki Limited Warranty Commercial Equipment

SZC specifications

Scag Power Equipment is renowned for delivering quality lawn care equipment, and the Scag SZC series exemplifies this commitment to excellence. Designed specifically for landscape professionals and serious homeowners, the SZC combines power, precision, and user-friendly features to make mowing more efficient and enjoyable.

At the heart of the Scag SZC is its powerful engine options. The mower comes equipped with reliable engines from leading manufacturers, including Kohler and Vanguard. These engines provide robust performance, ensuring that users can tackle even the most challenging mowing tasks with ease. The enhanced torque and power translate into faster mowing speeds without compromising cutting quality, allowing operators to cover more ground in less time.

One of the standout features of the Scag SZC is its innovative cutting deck design. The mower boasts a patented Velocity Plus deck, which enhances airflow and grass flow for superior cutting and bagging performance. This design not only leaves a clean, manicured finish but also minimizes clumping in wet conditions, ensuring optimal results every time. Available in multiple cutting widths, the SZC accommodates various lawn sizes and shapes, offering flexibility for different mowing situations.

The SZC is equipped with advanced technology that enhances user experience and operational efficiency. The intuitive controls and ergonomic seating ensure comfort during prolonged use, reducing operator fatigue. Its hydrostatic transmission allows for smooth operation, enabling users to navigate complex terrains effortlessly. The enhanced maneuverability ensures that users can easily tackle tight spots and intricate landscaping features, making it ideal for both commercial and residential applications.

Durability is another hallmark of the Scag SZC. Built with high-quality materials and a rugged frame, the mower is designed to withstand the rigors of regular use. The heavy-duty construction not only extends the life of the mower but also enhances stability during operation, making it safe and reliable.

Furthermore, the Scag SZC is engineered with maintenance efficiency in mind. Accessible components facilitate easy servicing, reducing downtime and ensuring that the mower remains in peak operational condition. Maintenance reminders built into the system help users keep track of service intervals, promoting a proactive approach to care.

In conclusion, the Scag Power Equipment SZC series offers a combination of power, precision, and practicality. With its robust engine options, innovative cutting technology, comfortable controls, and durable construction, it is a top choice for anyone looking to elevate their lawn care experience. Whether you're a professional landscaper or a dedicated homeowner, the Scag SZC can meet and exceed your mowing expectations.
Top Page Image Contents