Scag Power Equipment SZC manual Reverse Travel, Engaging the Deck Drive Cutter Blades

Page 19

Section 4

To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right.

-NOTE-

Smooth operation of the steering levers will produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

-IMPORTANT-

Do not travel forward over a curb. The mower may hang up on the curb. Raise the deck and travel backwards over the curb at a 45 degree angle. (see section 4.1, item 12 for cutter deck raising instructions)

Reverse Travel

CAUTION:

Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.

CAUTION:

Before backing up, observe the rear for persons and obstructions. Clear the area before backing up. Possible injury or property damage could occur.

To steer right while traveling in reverse, allow the right steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn right.

To stop the reverse travel, allow the steering control levers to return to the neutral position. If the mower is to be parked, place the handles in the neutral lock position and engage the parking brake.

4.6ENGAGING THE DECK DRIVE (CUTTER BLADES)

1.Set the throttle at about 3/4 speed. Do not attempt to engage the deck drive at high speed as this shortens the electric clutch life — use only moderate engine speed when engaging the deck drive.

2.Engage the deck drive by pulling out on the yellow switch, located on the instrument panel, (Figure 4-3) to the engage position.

-NOTE-

A squealing noise may be heard when engaging or disengaging the deck drive. It is caused by the electric clutch plates meshing as the mower comes up to speed. This is normal.

To travel in reverse, pull levers inward out of the neutral lock position and pull both handles back. Keep the travel speed low while traveling in reverse.

-NOTE-

The mower may not travel straight in reverse. Slight adjustments must be made using the steering controls.

To steer left while traveling in reverse, allow the left steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn left.

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

STT99CES

Figure 4-3 Cutter Deck Engage Switch

15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Servicing the Engine and Drive Train Components General InformationIntroduction Direction ReferenceISO Symbols CE Mark Fast Slow Signal Words Safety InformationBefore Operation Considerations Operation Considerations Before Operation Considerations ContdRoll Over Protection System Operation Considerations ContdSeat Belt Inspection SZC With Optional Roll Over Protection System Maintenance Considerations & StorageSafety and Instructional Decals Tractor SpecificationsEngine ElectricalProductivity Tractor ContdCutter Deck Hydraulic SystemStart Dump Valve Control Safety Interlock SystemGround Travel and Steering Starting the EngineForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Hillside OperationRecommendations for Mowing Adjusting Cutting HeightRemoving Clogged Material Moving Mower with Engine StoppedDeck Release Lever Condition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdParking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Alignment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AdjustmentCutter Deck Level Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Custom-Cut Baffle AdjustmentCustom-Cut Baffle Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OILCleaning and/or Replacing Air Cleaner Element Engine AIR CleanerBattery Jump Starting Charging the BatteryBlade Inspection Blade ReplacementDrive Belts Cutter BladesBODY, DECK, and Upholstery TiresSection 36A& 42A Cutter Decks Part Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Sheet Metal Components SZC Roll Over Protection System Ref. Part No. No. Description Drive System Components Drive System Components Engine and Attaching Parts Part Description To Pump Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Heavy-Duty Commercial 482166R SZC 2005 RDP2 Electrical Schematic Kawasaki Limited Warranty Commercial Equipment

SZC specifications

Scag Power Equipment is renowned for delivering quality lawn care equipment, and the Scag SZC series exemplifies this commitment to excellence. Designed specifically for landscape professionals and serious homeowners, the SZC combines power, precision, and user-friendly features to make mowing more efficient and enjoyable.

At the heart of the Scag SZC is its powerful engine options. The mower comes equipped with reliable engines from leading manufacturers, including Kohler and Vanguard. These engines provide robust performance, ensuring that users can tackle even the most challenging mowing tasks with ease. The enhanced torque and power translate into faster mowing speeds without compromising cutting quality, allowing operators to cover more ground in less time.

One of the standout features of the Scag SZC is its innovative cutting deck design. The mower boasts a patented Velocity Plus deck, which enhances airflow and grass flow for superior cutting and bagging performance. This design not only leaves a clean, manicured finish but also minimizes clumping in wet conditions, ensuring optimal results every time. Available in multiple cutting widths, the SZC accommodates various lawn sizes and shapes, offering flexibility for different mowing situations.

The SZC is equipped with advanced technology that enhances user experience and operational efficiency. The intuitive controls and ergonomic seating ensure comfort during prolonged use, reducing operator fatigue. Its hydrostatic transmission allows for smooth operation, enabling users to navigate complex terrains effortlessly. The enhanced maneuverability ensures that users can easily tackle tight spots and intricate landscaping features, making it ideal for both commercial and residential applications.

Durability is another hallmark of the Scag SZC. Built with high-quality materials and a rugged frame, the mower is designed to withstand the rigors of regular use. The heavy-duty construction not only extends the life of the mower but also enhances stability during operation, making it safe and reliable.

Furthermore, the Scag SZC is engineered with maintenance efficiency in mind. Accessible components facilitate easy servicing, reducing downtime and ensuring that the mower remains in peak operational condition. Maintenance reminders built into the system help users keep track of service intervals, promoting a proactive approach to care.

In conclusion, the Scag Power Equipment SZC series offers a combination of power, precision, and practicality. With its robust engine options, innovative cutting technology, comfortable controls, and durable construction, it is a top choice for anyone looking to elevate their lawn care experience. Whether you're a professional landscaper or a dedicated homeowner, the Scag SZC can meet and exceed your mowing expectations.
Top Page Image Contents