Scag Power Equipment SZC manual Cutter Deck Height, Custom-Cut Baffle Adjustment

Page 30

Section 6

Cutter Deck Height

The cutter deck height adjustment is made to ensure that the cutter deck is cutting at the height indicated on the cutting height index gauge. To check for proper deck height, be sure that the mower is on a flat, level surface and the tires are properly inflated.

1.Place the cutter deck in the transport position. Loosen the jam nuts on both ends of the deck height control rod. (See Figure 6-5)

LOOSEN

HERE

CONTROL ROD

Figure 6-5. Cutter Deck Height Adjustment

2.Turn the control rod (See Figure 6-6) until there is a 1/4" space between the rear deck stop and the top of the cutter deck. (See Figure 6-6). Tighten the jam nuts on the control rod.

3.Check the cutter deck cutting height by placing the lanyard pin in the 3" position on the cutting height index. Release the deck from the transport positon and allow the deck to move to the 3" cutting height position.

4.Check the measurement from the floor to the cutter blade tip. If the measurement is not at 3", an adjustment can be made using the deck height control rod. (See Figure 6-5)

-NOTE-

If an adjustment had to be made, be sure that the cutter deck can easily be locked into the transport position.

Custom-Cut Baffle Adjustment

The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut. The baffle can be set in three (3) different positions for optimum performance.

A.3" Position - baffle is installed using the top set of holes on the front baffle welded inside the cutter deck. (See Figure 6.8). The Advantage cutter deck will deliver the best quality-of-cut in very tall, wiry, tough to cut grass.

B.3-1/2" Position (factory setting) - baffle is installed using the middle set of holes on the front baffle welded inside the cutter deck. (See Figure 6.9). For general purpose cutting, place the Custom-Cut Baffle in the 3-1/2" position. This gives the best mix of cutting performance in all types of grass.

C.4" Position - baffle is installed using the bottom set of holes on the front baffle welded inside the cutter deck. (See Figure 6.10). Placing the baffle in the 4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

DECK STOP

1/4"

SZC 2005 CDS

Figure 6-6. Cutter Deck Stop

26

Image 30
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Direction Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Safety Information Signal WordsBefore Operation Considerations Before Operation Considerations Contd Operation ConsiderationsOperation Considerations Contd Roll Over Protection SystemSeat Belt Inspection Maintenance Considerations & Storage SZC With Optional Roll Over Protection SystemSafety and Instructional Decals Electrical SpecificationsEngine TractorHydraulic System Tractor ContdCutter Deck ProductivityStart Safety Interlock System Dump Valve ControlStarting the Engine Ground Travel and SteeringForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Parking the MowerMoving Mower with Engine Stopped Adjusting Cutting HeightRemoving Clogged Material Recommendations for MowingDeck Release Lever Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentBelt Adjustment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AlignmentCutter Deck Adjustments Cutter Deck LevelCutter Deck Pitch Custom-Cut Baffle Adjustment Cutter Deck HeightCustom-Cut Baffle Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine OIL Engine Fuel SystemEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner ElementBattery Charging the Battery Jump StartingCutter Blades Blade ReplacementDrive Belts Blade InspectionTires BODY, DECK, and UpholsterySection 36A& 42A Cutter Decks Part Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Sheet Metal Components SZC Roll Over Protection System Ref. Part No. No. Description Drive System Components Drive System Components Engine and Attaching Parts Part Description To Pump Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Heavy-Duty Commercial 482166R SZC 2005 RDP2 Electrical Schematic Kawasaki Limited Warranty Commercial Equipment

SZC specifications

Scag Power Equipment is renowned for delivering quality lawn care equipment, and the Scag SZC series exemplifies this commitment to excellence. Designed specifically for landscape professionals and serious homeowners, the SZC combines power, precision, and user-friendly features to make mowing more efficient and enjoyable.

At the heart of the Scag SZC is its powerful engine options. The mower comes equipped with reliable engines from leading manufacturers, including Kohler and Vanguard. These engines provide robust performance, ensuring that users can tackle even the most challenging mowing tasks with ease. The enhanced torque and power translate into faster mowing speeds without compromising cutting quality, allowing operators to cover more ground in less time.

One of the standout features of the Scag SZC is its innovative cutting deck design. The mower boasts a patented Velocity Plus deck, which enhances airflow and grass flow for superior cutting and bagging performance. This design not only leaves a clean, manicured finish but also minimizes clumping in wet conditions, ensuring optimal results every time. Available in multiple cutting widths, the SZC accommodates various lawn sizes and shapes, offering flexibility for different mowing situations.

The SZC is equipped with advanced technology that enhances user experience and operational efficiency. The intuitive controls and ergonomic seating ensure comfort during prolonged use, reducing operator fatigue. Its hydrostatic transmission allows for smooth operation, enabling users to navigate complex terrains effortlessly. The enhanced maneuverability ensures that users can easily tackle tight spots and intricate landscaping features, making it ideal for both commercial and residential applications.

Durability is another hallmark of the Scag SZC. Built with high-quality materials and a rugged frame, the mower is designed to withstand the rigors of regular use. The heavy-duty construction not only extends the life of the mower but also enhances stability during operation, making it safe and reliable.

Furthermore, the Scag SZC is engineered with maintenance efficiency in mind. Accessible components facilitate easy servicing, reducing downtime and ensuring that the mower remains in peak operational condition. Maintenance reminders built into the system help users keep track of service intervals, promoting a proactive approach to care.

In conclusion, the Scag Power Equipment SZC series offers a combination of power, precision, and practicality. With its robust engine options, innovative cutting technology, comfortable controls, and durable construction, it is a top choice for anyone looking to elevate their lawn care experience. Whether you're a professional landscaper or a dedicated homeowner, the Scag SZC can meet and exceed your mowing expectations.