Scag Power Equipment STT61V-29DFI, STT-29DFI, STT61V-35BVAC manual Engine Oil, Engine Fuel System

Page 41

Section 7

R

C. Changing Hydraulic Oil Filter Element

The hydraulic oil filter should be changed after every 500 hours of operation or annually, whichever occurs first.

1.Remove the oil filter element and properly discard it. See Figure 7-3. Fill the new filter with clean oil and install the filter. Hand tighten only.

2.Run the engine at idle speed with the speed control lever in neutral for five minutes.

3.Check the oil level in the hydraulic tank. It must be 3-1/4" inches from the top of the filler neck. If necessary, add SAE 20W50 motor oil.

7.4 Engine Oil

ENGINE OIL

DIPSTICK

390S0156

Figure 7-4. Engine Oil Fill/Dipstick Location

A. Checking Engine Crankcase Oil Level

The engine oil level should be checked after every 8 hours of operation or daily as instructed in the Engine Operator’s Manual furnished with this mower.

B. Changing Engine Crankcase Oil

After the first 20 hours of operation, change the engine crankcase oil and replace the oil filter. Thereafter, change the engine crankcase oil after every 100 hours of operation or bi-weekly, whichever occurs first. Refer to the Engine Operator’s Manual furnished with this mower for instructions. See Figure 7-5.

ENGINE OIL FILTER

DRAIN

PLUG

STT99CEC

Figure 7-5. Drain Plug and Oil Filter Location

C. Changing Engine Oil Filter

After the first 20 hours of operation, replace the engine oil filter. Thereafter, replace the oil filter after every 200 hours of operation or every month, whichever occurs first. Refer to Engine Operator’s Manual for instructions. See Figure 7-5.

7.5 Engine Fuel System

DANGER

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

A. Filling the Fuel Tank

Fill the fuel tank at the beginning of each operating day. For EPA Phase 2 (produced prior to 1/1/2011) models, fill to within one (1) inch below the filler neck. For Low Emission (LE) and EPA Phase 3 (produced after 1/1/2011) models, fill to the bottom of the filler neck insert (approximately 8-1/2 gallons indicating Full (F) on the fuel gauge) at the beginning of each operating day. See Figure 7-6. Do not overfill. Use clean, fresh unleaded gasoline with a minimum octane rating of 87 and a maximum of 10% Ethanol.

DO NOT use E85 Fuel. Using E85 Fuel will cause severe damage to the engine.

35

Page 40 Page 42
Image 41
Page 40 Page 42
Contents OPERATOR’S Manual STT-35BVAC Remember Your Mower is only AS Safe AS the OperatorTable of Contents Troubleshooting Cutting Conditions Adjustments Limited Warranty Commercial Equipment Table of Contents Servicing The Engine And Drive Train Components IntroductionDirection Reference Symbol Description SymbolsSafety Information Operation Considerations Section ROLL-OVER Protection System Seat Belt Inspection Spark Ignition System Forward Reverse Electrical EngineCutter Deck Power HeadHydraulic System Weights And Dimensions 52V 61VProductivity 52V 61V 72VSControls And Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemStarting The Engine Initial Run-In ProceduresGround Travel And Steering Forward TravelReverse Travel Engaging The Deck Drive Cutter BladesHillside Operation Rotating BladesAfter Operation Parking The MowerRecommendations For Mowing Adjusting Cutting HeightMoving Mower With Engine Stopped Adjusting The Height Adjust Pedal Adjusting The Steering LeversTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsTracking Adjustment Throttle Control And Choke AdjustmentsBelt Adjustment Belt Alignment Cutter Deck AdjustmentsCutter Deck Level Cutter Deck PitchCutter Deck Height Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment 10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilReplacing In-Line Fuel Filter Elements Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Charging the Battery BatteryCutter Blades Drive BeltsJump Starting Blade InspectionTires Blade ReplacementCooling System Cutter Deck GearboxChecking The Fan Belt Tension Liquid- Cooled Engines Only Cleaning the Radiator Debris ScreenBody, Deck, And Upholstery Section Scag Approved Attachments And Accessories Illustrated Parts ListSection Description 52V Cutter Deck61V & 72VS Cutter Decks Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 9278 STT ROLL-OVER Protection System STT ROLL-OVER Protection System STT Suspension Seat Section Deck Drive Components 35BVAC Engine and Attaching Parts Kohler Available through the individual engine manufacturer Engine & Attaching Parts 27HP, 29DFI Kawasaki & 35BVAC Engine & Attaching Parts 27HP, 29DFI Kawasaki & 35BVAC Brake and Steering Components Bolt, Carriage 5/16-18 x STT Hydraulic System Base Fuel Models produced prior to 1/1/2011 STT Fuel System EPA PhaseSTT Fuel System EPA Phase 3 models produced after 1/1/2011 STT Fuel System EPA Phase STT FS Carb Teir 3 Rev2.eps STT-LE Fuel System C.A.R.B. Tier BDP-16A Hydraulic Pump Assembly BDP-16A Hydraulic Pump Assembly Port a Side Hex Screw, Flanged Head M10 x 1.50-65mm Section Electrical System Kohler & Briggs & Stratton Instrument Panel, Top w/Decals Electrical System 27HP Kawasaki Electrical System 27HP Kawasaki Electrical System 29DFI Kawasaki Electrical System 29DFI Kawasaki Heavy-Duty Replacement Decals and Information Plates1617 STT Electrical Schematic Kohler Engine STT Electrical Schematic 27HP KawasakiRelay Electrical Schematic 29DFI KawasakiSection STT Electrical Schematic 35BVAC Briggs & Stratton Limited Warranty Commercial Equipment

STT-35BVAC, STT61V-29DFI-LE, STT61V-35BVAC, STT61V-29DFI, STT-29DFI specifications

Scag Power Equipment is renowned for its high-quality lawn care machinery, and among its range of products, the STT series stands out, particularly the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, and STT-35BVAC models. These zero-turn mowers are designed to deliver exceptional performance, durability, and efficiency, catering to both commercial landscapers and homeowners alike.

The STT-29DFI offers an impressive 29 horsepower, powered by a state-of-the-art EFI engine. This model boasts an advanced deck design, featuring a robust 61-inch cutting width that ensures a clean and even cut. The mower's zero-turn capability allows for enhanced maneuverability, making it easier to navigate around obstacles and achieve a professional finish.

In comparison, the STT61V-35BVAC takes power to the next level with a 35 horsepower engine. This model is perfect for tackling larger areas and more challenging terrains. The vacuum-assisted cutting system effectively collects clippings, reducing cleanup time after mowing. The heavy-duty, reinforced steel frame ensures long-lasting durability, while the comfortable operator seat and control system enhance user experience.

The STT61V-29DFI is another remarkable addition to this lineup, featuring a 29 horsepower engine equipped with EFI technology. This model focuses on fuel efficiency, allowing operators to maximize output while minimizing fuel consumption. With its 61-inch cutting deck, it provides an excellent balance between power and precision, ideal for both commercial and residential use.

For those looking for a more specialized option, the STT61V-29DFI-LE includes enhancements aimed at professional landscapers, such as a premium seat suspension system for extended comfort during long operating hours. This model also features a customizable control panel, making it easier for operators to tailor settings to their specific needs.

Lastly, the STT-35BVAC integrates a robust 35 horsepower engine, along with advanced features that promote efficiency and productivity. This model's design prioritizes user-friendly operation, with intuitive controls and easy access to maintenance points. The vacuum system further enhances its capabilities by collecting grass clippings and debris as you mow, ensuring a tidy lawn at all times.

In summary, Scag Power Equipment's STT series is characterized by powerful engine options, advanced cutting technologies, and a commitment to durability and operator comfort. Whether you choose the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, or STT-35BVAC, you can expect a mower that stands up to the demands of any lawn care task.
Top Page Image Contents