Scag Power Equipment STT61V-35BVAC Engine Air Cleaner, Replacing In-Line Fuel Filter Elements

Page 42

R

Section 7

FILLER NECK

INSERT

1/2.

1/4. .3/4 E. .F

FUEL LEVEL

Figure 7-6. C.A.R.B. / EPA Phase 3 Fuel Level

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

1.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

2.Use only an approved gasoline container.

3.Never remove the gas cap or add fuel with the engine running. Allow the engine to completely cool before fueling.

4.Never fuel the machine indoors or in an enclosed trailer.

5.Never store the machine or fuel container where there is an open flame, spark or pilot light such as on a water heater or other appliances.

6.Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

7.Remove the machine from the truck or trailer and fuel on the ground. If this is not possible, then refuel the machine with a portable container, rather than from a gasoline dispenser nozzle.

8.Keep the nozzle in contact with the rim of fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

9.If fuel is spilled on clothing, change clothing immediately and wash affected skin.

10.Replace gas cap and tighten securely. For Low Emission (LE) and EPA Phase 3 (produced after 1/1/2011) models, tighten the fuel cap until it ratchets.

B. Replacing In-Line Fuel Filter Elements

The engine fuel filter should be replaced after every 500 hours of operation or annually, whichever occurs first. See Figure 7-6.

1.Close the shut-off valve.

2.Remove the two clamps securing the fuel filter to the fuel hose. Remove the fuel filter.

3.Install a new fuel filter. Be sure it is installed in the proper direction. Secure to the fuel hose using the two clamps.

4.Open the fuel shut-off valve.

Fuel Filter

(with hose clamps above and below)

STT99FF-1

Figure 7-7. Fuel Filter

7.6 Engine Air Cleaner

A. Cleaning and/or Replacing Air Cleaner Element

For any air cleaner, the operating environment dictates the air cleaner service periods. Inspect and clean the air cleaner element after every 100 hours of operation or bi-weekly, whichever occurs first and replace the element if required. See Engine Owner's Manual for service information.

36

Page 41 Page 43
Image 42
Page 41 Page 43
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator STT-35BVACTable of Contents Troubleshooting Cutting Conditions Adjustments Limited Warranty Commercial Equipment Table of Contents Introduction Direction ReferenceServicing The Engine And Drive Train Components Symbols Symbol DescriptionSafety Information Operation Considerations Section ROLL-OVER Protection System Seat Belt Inspection Spark Ignition System Forward Reverse Engine ElectricalPower Head Cutter DeckProductivity 52V 61V Weights And Dimensions 52V 61VHydraulic System 72VSOperating Instructions Controls And Instrument IdentificationSafety Interlock System Dump Valve ControlGround Travel And Steering Initial Run-In ProceduresStarting The Engine Forward TravelEngaging The Deck Drive Cutter Blades Reverse TravelAfter Operation Rotating BladesHillside Operation Parking The MowerAdjusting Cutting Height Moving Mower With Engine StoppedRecommendations For Mowing Adjusting The Steering Levers Adjusting The Height Adjust PedalTowing Optional Hitch Accessory Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Cut, or Rough ContourScalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentThrottle Control And Choke Adjustments Belt AdjustmentTracking Adjustment Cutter Deck Level Cutter Deck AdjustmentsBelt Alignment Cutter Deck PitchCustom-Cut Baffle Adjustment Cutter Deck HeightPosition Custom-Cut Baffle Adjustment Electric clutch adjustment 10. Clutch Air Gap AdjustmentMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemEngine Air Cleaner Cleaning and/or Replacing Air Cleaner ElementReplacing In-Line Fuel Filter Elements Battery Charging the BatteryJump Starting Drive BeltsCutter Blades Blade InspectionBlade Replacement TiresCutter Deck Gearbox Cooling SystemCleaning the Radiator Debris Screen Body, Deck, And UpholsteryChecking The Fan Belt Tension Liquid- Cooled Engines Only Section Illustrated Parts List Scag Approved Attachments And AccessoriesSection 52V Cutter Deck Description61V & 72VS Cutter Decks Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 9278 STT ROLL-OVER Protection System STT ROLL-OVER Protection System STT Suspension Seat Section Deck Drive Components 35BVAC Engine and Attaching Parts Kohler Available through the individual engine manufacturer Engine & Attaching Parts 27HP, 29DFI Kawasaki & 35BVAC Engine & Attaching Parts 27HP, 29DFI Kawasaki & 35BVAC Brake and Steering Components Bolt, Carriage 5/16-18 x STT Hydraulic System Base Fuel STT Fuel System EPA Phase Models produced prior to 1/1/2011STT Fuel System EPA Phase 3 models produced after 1/1/2011 STT Fuel System EPA Phase STT FS Carb Teir 3 Rev2.eps STT-LE Fuel System C.A.R.B. Tier BDP-16A Hydraulic Pump Assembly BDP-16A Hydraulic Pump Assembly Port a Side Hex Screw, Flanged Head M10 x 1.50-65mm Section Electrical System Kohler & Briggs & Stratton Instrument Panel, Top w/Decals Electrical System 27HP Kawasaki Electrical System 27HP Kawasaki Electrical System 29DFI Kawasaki Electrical System 29DFI Kawasaki Replacement Decals and Information Plates Heavy-Duty1617 STT Electrical Schematic Kohler STT Electrical Schematic 27HP Kawasaki EngineElectrical Schematic 29DFI Kawasaki RelaySection STT Electrical Schematic 35BVAC Briggs & Stratton Limited Warranty Commercial Equipment

STT-35BVAC, STT61V-29DFI-LE, STT61V-35BVAC, STT61V-29DFI, STT-29DFI specifications

Scag Power Equipment is renowned for its high-quality lawn care machinery, and among its range of products, the STT series stands out, particularly the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, and STT-35BVAC models. These zero-turn mowers are designed to deliver exceptional performance, durability, and efficiency, catering to both commercial landscapers and homeowners alike.

The STT-29DFI offers an impressive 29 horsepower, powered by a state-of-the-art EFI engine. This model boasts an advanced deck design, featuring a robust 61-inch cutting width that ensures a clean and even cut. The mower's zero-turn capability allows for enhanced maneuverability, making it easier to navigate around obstacles and achieve a professional finish.

In comparison, the STT61V-35BVAC takes power to the next level with a 35 horsepower engine. This model is perfect for tackling larger areas and more challenging terrains. The vacuum-assisted cutting system effectively collects clippings, reducing cleanup time after mowing. The heavy-duty, reinforced steel frame ensures long-lasting durability, while the comfortable operator seat and control system enhance user experience.

The STT61V-29DFI is another remarkable addition to this lineup, featuring a 29 horsepower engine equipped with EFI technology. This model focuses on fuel efficiency, allowing operators to maximize output while minimizing fuel consumption. With its 61-inch cutting deck, it provides an excellent balance between power and precision, ideal for both commercial and residential use.

For those looking for a more specialized option, the STT61V-29DFI-LE includes enhancements aimed at professional landscapers, such as a premium seat suspension system for extended comfort during long operating hours. This model also features a customizable control panel, making it easier for operators to tailor settings to their specific needs.

Lastly, the STT-35BVAC integrates a robust 35 horsepower engine, along with advanced features that promote efficiency and productivity. This model's design prioritizes user-friendly operation, with intuitive controls and easy access to maintenance points. The vacuum system further enhances its capabilities by collecting grass clippings and debris as you mow, ensuring a tidy lawn at all times.

In summary, Scag Power Equipment's STT series is characterized by powerful engine options, advanced cutting technologies, and a commitment to durability and operator comfort. Whether you choose the STT-29DFI, STT61V-35BVAC, STT61V-29DFI, STT61V-29DFI-LE, or STT-35BVAC, you can expect a mower that stands up to the demands of any lawn care task.
Top Page Image Contents