Scag Power Equipment STT manual Checking Electrolyte Level and Cleaning Battery

Page 32

Section 7

7.7 BATTERY

A. Checking Electrolyte Level and Cleaning Battery

After every 40 hours of operation or weekly, whichever occurs first, check the electrolyte level in the battery and clean the battery and connections. Dirt and fluid on the top of the battery can cause the battery to discharge.

Corrosion of the battery terminals or loose connections will cause poor battery performance.

WARNING:

Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. Keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.

1.Loosen the two plastic wing nuts and then remove the battery cover.

2.Remove the battery cell caps. Visually inspect electrolyte level in the cells. If electrolyte is

below the bottom of vent well, fill with clean distilled water to the bottom of vent wells (1/4 to 1/2 inch above the plates). Install the battery cell caps.

-IMPORTANT-

Do not overfill the battery. Electrolyte will overflow through the vent tube onto parts of the machine, resulting in severe corrosion.

3.Clean the cable ends and battery posts with steel wool. Use a solution of baking soda and water to clean the battery. Do not allow the solution to enter the battery cells.

4.Tighten the cable connections securely and apply a light coat of silicone dielectric grease to the terminal connections to prevent corrosion.

5.Install the battery cover.

WARNING:

Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEVERE CHEMICAL BURNS. Avoid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NOT tip any battery beyond 45° angle in any direction. If fluid contact does occur, follow first aid suggestions below.

BATTERY ELECTROLYTE FIRST AID

EXTERNAL CONTACT — Flush with water.

EYES — Flush with water for at least 15 minutes and get medical attention immediately.

INTERNAL — Drink large quantities of water. Follow with Milk Of Magnesia, beaten egg,

or vegetable oil. Get medical attention immediately. In case of internal contact, DO NOT give fluids that would induce vomiting.

B. Charging the Battery

Refer to the battery charger’s manual for specific instructions.

Under normal conditions the engine’s alternator will have no problem keeping a charge on the battery. If the battery has been completely discharged for a long period of time, the alternator may not be able to recharge the battery, and a battery charger will be required.

DO NOT charge a frozen battery. It may explode and cause injury. Let the battery warm before attaching a charger.

Whenever possible, remove the battery from the mower before charging and make sure the electrolyte covers the plates in all cells.

29

Page 31 Page 33
Image 32
Page 31 Page 33
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Servicing the Engine and Drive Train Components IntroductionDirection Reference Signal Words Before Operation ConsiderationsBefore Operation Considerations Contd Operation ConsiderationsMaintenance Considerations Operation Considerations ContdRotating Blades and Belts Safety and Instructional Decals Spinning BladeStart / Drive Procedure Tractor EngineElectrical Weights and Dimensions Model Tractor ContdCutter Deck Hydraulic SystemSection Operating Instructions Controls and Instrument IdentificationSafety Interlock System Forward Travel Ground Travel and SteeringStarting the Engine Reverse Travel Engaging the Deck Drive Cutter BladesAfter Operation Hillside OperationParking the Mower Rotating Blades Removing Clogged MaterialMoving Mower with Engine Stopped Recommendations for MowingAdjusting Cutting Height Deck Release LeverTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundParking Brake Adjustment Travel AdjustmentsNeutral Adjustment RH Steering Control Rod AdjustmentTracking Adjustment Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Adjustment Cutter Deck HeightMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilChanging Hydraulic Oil Filter Element Engine OILChecking Engine Crankcase Oil Level Changing Engine Crankcase OilEngine AIR Cleaner Engine Fuel SystemCharging the Battery BatteryChecking Electrolyte Level and Cleaning Battery Jump Starting Drive BeltsBlade Sharpening Cutter BladesBlade Replacement TiresCutter Deck Gearbox Checking Lubricant LevelKawasaki Cooling System Checking Coolant LevelBODY, DECK, and Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Section 52 & 61 Cutter Decks 52& 61 Cutter Decks Ref. Part DescriptionCutter Deck CONTROLS, 52 & 61 Decks Cutter Deck CONTROLS, 52 & 61 Decks Part DescriptionSheet Metal Components Sheet Metal Components Deck Drive Components Deck Drive Components Engine and Attaching Parts Kohler Engine and Attaching Parts Kohler Engine and Attaching Parts Kawasaki Engine and Attaching Parts Kawasaki Brake and Steering Components Brake and Steering Components Fuel and Hydraulic System Fuel and Hydraulic System Electrical System Kohler Electrical System Kohler Electrical System Kawasaki Electrical System Kawasaki Hydraulic Pump Assembly Housing Kit Includes Housing, Journal Bearing Replacement Decals and Information Plates Operating Machine2018 Electrical Schematic Kohler Electrical Schematic Kawasaki Limited WARRANTY-COMMERCIAL Equipment 1998
Top Page Image Contents