Scag Power Equipment STT61V-29KB-DF manual Adjustments, Parking Brake Adjustment

Page 27

Section 6

R

ADJUSTMENTS

6.1 PARKING BRAKE ADJUSTMENT

WARNING

Do not operate the mower if the parking brake is not operable. Possible severe injury could result.

The parking brake linkage should be adjusted whenever the parking brake lever is placed in the “ENGAGE” position and the parking brake will allow the mower to move. If the following procedures do not allow you to engage the parking brake properly, contact your Scag dealer for further brake adjustments.

- NOTE -

If this procedure does not achieve proper brake adjustment, please contact your authorized Scag dealer.

LOOSEN HERE

1. Position a floor jack under the rear of the machine.

Raise the machine and support it to prevent it

from falling. Block the caster wheels to prevent the

2" to 2-1/4" Clearance

390S0152-1

 

machine from moving. Remove the drive wheels.

2.

With the brake lever in the disengaged position,

 

check the distance between the top of the frame

 

tube and the bottom of the brake handle. The

 

distance should be 2" to 2-1/4" (See Figure 6-1).

3.

If the distance is not at the specified measurement,

 

adjust by loosening the jam nuts at both ends of the

 

brake control rod and turning the rod until the proper

 

distance is achieved. (See Figure 6-1). Tighten the

 

jam nuts.

4.

With the brake in the engaged position, check the

 

spring compression between the two flat washers on

 

the LH side of the machine. The distance should be

 

1-7/16". (See Figure 6-2).

5.

If the distance is not at the specified measurement,

 

loosen the jam nut at the rod end side of the brake

 

actuator rod. (See Figure 6-2).

6.

Turn the adjustment bolt (clockwise to decrease

 

the spring compression or counter clockwise to

 

increase the spring compression) until the 1-7/16"

 

measurement is achieved and tighten the jam nut.

 

(See Figure 6-2).

7.

Repeat steps 4 though 6 on the RH side of the

 

machine.

8.

Replace the drive wheels and test the brake.

Figure 6-1. Brake Adjustment

LOOSEN HERE

ADJUST HERE

Figure 6-2. Brake Rod Adjustment

23

Page 26 Page 28
Image 27
Page 26 Page 28
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Inside Back Cover AdjustmentsServicing The Engine And Drive Train Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsSafety Information Signal WordsBefore Operation Considerations Operation Considerations Section Foldable Roll-over protection system Roll-Over Protection SystemFoldable Roll-Over Protection System Using a spark arrestor Maintenance Considerations & StorageInstall Belt COvER Before Safety And Instructional DecalsElectrical SpecificationsPower Head EngineProductivity Weights And DimensionsCutter Deck Hydraulic SystemControls And Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemForward Travel Initial Run-In ProceduresStarting The Engine Ground Travel And SteeringReverse Travel Engaging The Deck Drive Cutter BladesAfter Operation Rotating BladesHillside Operation Parking The MowerAdjusting Cutting Height Moving Mower With Engine StoppedRecommendations For Mowing Adjusting The Height Adjust Pedal Adjusting The Steering LeversTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsTracking Adjustment Throttle Control and Choke AdjustmentsCutter Deck Pitch Cutter Deck LevelCutter Deck Height Cutter Deck Height AdjustmentCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilLpg fUel system Replacing In-Line Fuel Filter ElementsEngine Air Cleaner BatteryCleaning and/or Replacing Air Cleaner Element Cutter Blades Drive BeltsBlade Sharpening Blade ReplacementTires Cutter Deck GearboxCooling System Cleaning the Radiator Debris Screen Body, Deck, And UpholsteryChecking The Fan Belt Tension Liquid- Cooled Engines Only Illustrated Parts List Section 61V Cutter Deck Description Cutter Deck Controls 481764 Link, Deck Lift Sheet Metal Components Sheet Metal Components Section STT ROLL-OVER Protection System with Suspension Seat 9292 Deck Drive Components Deck Drive Components Engine & Attaching Parts Kubota Dual Fuel Available through the individual engine manufacturer Brake and Steering Components Description Gasoline and Hydraulic System Kubota Dual Fuel Hose Assy, 1/2 ID Tank to Filter Base LP System Kubota Dual Fuel LP System Kubota Dual Fuel Section BDP-16A Hydraulic Pump Assembly with Cooling Fan Hex Screw, Flanged Head M10 x 1.50-65mm Electrical System Kubota Dual Fuel Fuel Pump Forward R Reverse Replacement Decals and Information PlatesDUAL-FUEL Electrical Schematic Kubota Dual Fuel Limited Warranty Commercial Equipment

STT61V-29KB-DF specifications

The Scag Power Equipment STT61V-29KB-DF is a robust and powerful zero-turn mower designed for professional landscapers and homeowners seeking superior performance and efficiency. With a 61-inch cut width and a powerful 29 HP Kawasaki engine, this mower offers exceptional cutting capabilities, enabling users to tackle large lawns and challenging terrain with ease.

One of the standout features of the STT61V-29KB-DF is its patented Velocity Plus cutting deck. This innovative design enhances grass flow, resulting in a clean and precise cut. The deck's airflow is optimized to lift the grass for an even cut, ensuring a professional-quality finish every time. The mower's cutting height can be easily adjusted to suit different types of grass and seasonal conditions, providing versatility for various mowing tasks.

In addition to its performance features, the STT61V-29KB-DF is built with durability in mind. The heavy-duty steel frame and reinforced cutting deck provide lasting durability, allowing it to withstand the demands of frequent use in tough environments. The mower also boasts a high-quality paint finish that protects against rust and corrosion, ensuring the machine remains in great condition even after years of use.

The ergonomic design of the STT61V-29KB-DF enhances operator comfort and control. The cushioned seat provides support for long mowing sessions, while the easy-to-use joystick controls allow for smooth maneuverability and precise handling. This design reduces operator fatigue and increases productivity, making it a favorite among landscape professionals.

Another notable technology in the STT61V-29KB-DF is its hydrostatic transmission, which provides seamless speed and direction changes without the need for gear shifting. This feature allows for superior control and responsiveness, especially when navigating around obstacles or tight spaces.

Safety features are also prioritized in the design of this mower. It includes an automatic safety shut-off system that stops the blades when the operator leaves the seat, while the robust structure provides stability on slopes and uneven terrain.

Overall, the Scag Power Equipment STT61V-29KB-DF is a top-tier zero-turn mower that combines power, performance, and user-friendly features, making it an ideal choice for anyone looking to achieve a flawless cut while ensuring maximum operator comfort and safety. With its blend of advanced technologies and durability, this model stands out in the competitive market of landscaping equipment.
Top Page Image Contents