Scag Power Equipment SW manual Transmission Drive Belt, Drive Control Adjustments

Page 14

CUTTER DECK BELT ADJUSTMENTS (CONT'D)

BELT TENSION

CUTTER DECK

ADJUSTMENT IDLER

ADJUSTMENT

 

IDLER

 

 

DISCHARGE

AREA

CHECK BLADE DRIVE

SC402G

 

BELT TENSION HERE

 

Figure 3. Cutter Deck Belt

4. Replace the belt cover.

TRANSMISSION DRIVE BELT

Adjust the transmission drive belt so that there is about a 3/16" deflection with 10 lbs. of pressure. Adjust by loosening idler pulley mounting bolt and sliding the idler left or right to change belt tension.

DRIVE CONTROL ADJUSTMENTS

1.Adjust the steering control rods so that there is approximately 3/4" clearance from the bottom of the rod to the bottom of the neutral latch slot when in the

drive position. (See Figure 4)

Neutral

Latch

Neutral Lock

Position

Drive Position

3/4"

Steering

Brake Lever

SC404GB05

-NOTE-

Operator presence lever removed for clarity.

Never operate equipment with the interlock system disconnected.

Figure 4. Steering Control Rod Adjustment

2.Adjust the steering brake rods so that the brakes do not apply until the steering levers are pulled tight to the handles. When the steering levers are locked in the neutral position the machine should move freely.

CUTTER DECK ADJUSTMENTS

Due to the many cutting conditions that exist, it is difficult to suggest a cutter deck setting that will work for every lawn. There are two adjustments that can be made on these decks, pitch and height.

PITCH is the angle of the blades (comparing front to rear). A 1/4" downward pitch (front of deck down) is recommended for best cutting performance.

HEIGHT is the nominal distance the blade is off of the ground. This measurement is made with the blades pointed side to side and distance is measured between cutting tip and ground. (Also see Blade Height Adjust- ment, next page).

Changes to the cutting height can be achieved by reposi- tioning the cutter deck. (This adjustment will also effect the pitch of the deck). There are three available positions (See Figure 5).

LOW CUT (1 3/4" to 3")

MID RANGE (2 1/2" to 3 3/4")

HIGH CUT

(3 1/4" to 4 1/2")

SC405G-2

Figure 5. Cutting Height Adjustment

10

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model SW 2004Remember Your Mower is only AS Safe AS the Operator Table of Contents Model SW Table of Contents Direction Reference General InformationIntroduction Servicing the EngineISO Symbols CE Mark Fast Slow Before Operation Considerations Safety InformationGeneral Safety Information Before Operation Considerations Contd Rotating Blades Operation ConsiderationsMaintenance and Storage Operation Considerations ContdMaintenance and Storage Contd Mower OperationCutter Deck Belt Adjustments Mower Operation ContdCutter Deck Belt Adjustments Contd Drive Control AdjustmentsCutter Deck Adjustments Transmission Drive BeltCutter Blades Blade Height AdjustmentCutter Deck Adjustments Contd CUSTOM-CUT Baffle Adjustment To Adjust the CUSTOM-CUT Baffle HeightChecking Engine Crankcase OIL Level Engine AIR CleanerCleaning the Machine Changing Engine Crankcase OILLubrication & Maintenance Troubleshooting Cutting Conditions Condition Cause CureAppearance Uneven Cut on FlatGround Wavy High-Low Scalloped Cut, or Rough ContourGround Scalping BladesHitting Dirt or Cutting Very Close to Step CutEngine Technical SpecificationsModels Engine DeckApproximate Dimensions SWM36A SWM48A SWM52A SWM61A Technical Specifications ContAdditional Specifications Optional ITEMS/ATTACHMENTS Cutter Decks32 & 36A Cutter Decks Ref. Part No. Number Description 32 36A 48A, 52A Cutter Decks Part Description 48A 52A Page Caster Assembly Part 36A Description 48A 52AEngine Deck Part Handle Assembly 15KH 15KA 18HN Instrument Panel Part 15KH 15KA 18HN Description 18KH 17KAFor Reference Only Order Parts from Peerless / Tecumseh DescriptionHandle Wire Harness Manual Start Wire Harness Adapter Honda 18 HP Wire Harness Adapter481122 32 48315 36 482297 48 481953 52 482284 48314 482286482816 48404Install Belt Cover Before Operating MachineLimited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Opcionales ARTÍCULOS/ACCESORIOS SWM61A SWM52A SWM48A SWM36A Aproximadas DimensionesContinuación Técnicas Especificaciones Adicionales EspecificacionesMotor Técnicas EspecificacionesMotor DEL Plataforma ModelosCorte DE Condiciones LAS EN Fallas DE Identificación Solución Causa CondiciónIrregular perfil o La de ancho lo aInclinadas Salientes Volado corte onduladaDe Franjas Vetas Corte de trayectoriasPasadas entre entre cortar sin césped La en cortar sin céspedMantenimiento Y Lubricación Máquina LA DE Limpieza DEL Aceite DE Filtro DE CambioPersonalizado Personalizado Corte DE Deflector DEL AjusteDEL Altura LA Ajustar Para Personalizado Corte DE DeflectorContinuación Corte DE Plataforma LA DE Ajustes Corte DE CuchillasCorte DE Altura LA DE Ajuste Motriz Control DE Ajustes CorteDE Plataforma LA DE Ajustes Continuación Corte DE Plataforma LA DE Correa LA DE AjustesContinuación Cortacésped DEL Operación LA DE Correa LA DE AjustesNota Encendido del llave la quite y motor el DetengaCortacésped DEL Operación Continuación Almacenamiento Y MantenimientoAlmacenamiento Continuación Operación DE ConsideracionesContinuación Operación LA a Previas Consideraciones DE ConsideracionesGiratorias Cuchillas En transmisión la desconectada, esté plataforma AdvertenciaOperador el si motor el apaga sistema El .neutral De sistema un con equipada está máquina EstaLA a Previas Consideraciones Seguridad DE InformaciónOperación Seguridad DE General InformaciónDescripción Símbolo ISO Símbolos Instrucciones DE Referencia General InformaciónMotor AL Servicio Scag POR Aprobados Aditamentos Y AccesoriosPágina Contenido DE TablaTema SW Modelo Página TemaGraves Lesiones EN Resultar Puede Operación OperadorRecuerde DE Seguras Prácticas LAS DE Incumplimiento ELEquipment Power Scag UU.EE EN Impreso 2004 Julio EN Impreso 03145 .No Parte
Top Page Image Contents