Scag Power Equipment SW CUSTOM-CUT Baffle Adjustment, To Adjust the CUSTOM-CUT Baffle Height

Page 16

CUSTOM-CUT BAFFLE ADJUSTMENT

The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut. The baffle can be set in three (3) different positions for optimum performance.

A.3" Position - baffle is installed using the top set of holes on the front baffle welded inside the cutter deck. (See Figure 10). The Advantage cutter deck will deliver the best quality-of-cut in very tall, wiry, tough to cut grass.

B.3-1/2" Position (factory setting) - baffle is installed using the middle set of holes on the front baffle welded inside the cutter deck. (See Figure 11). For general purpose cutting, place the Custom Cut Baffle in the 3-1/2" position. This gives the best mix of cutting performance in all types of grass.

C.4" Position - baffle is installed using the bottom set of holes on the front baffle welded inside the cutter deck. (See Figure 12). Placing the baffle in the 4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

TO ADJUST THE CUSTOM-CUT BAFFLE HEIGHT:

1.Remove the hardware securing the Custom-Cut Baffle to the cutter deck (See Figure 9).

-NOTE-

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on the cutter deck size.

2.Move the Custom-Cut Baffle to desired position. (See Figures 10 through 12 for position)

3.Reinstall the mounting hardware as shown. (See Figures 10 though 12). Torque hardware to 39ft.lbs.

TOP SET OF HOLES

CARRIAGE BOLT

FOR 3" SETTING

 

2004 CCB - 3" Setting

ELASTIC STOP

NUT

Figure 10. 3" Custom-Cut Baffle Position

MIDDLE SET OF HOLES

CARRIAGE BOLT

FOR 3-1/2" SETTING

 

2004 CCB - 3-1/2" Setting

ELASTIC STOP

NUT

Figure 11. 3-1/2" Custom-Cut Baffle Position

BOTTOM SET OF HOLES

CARRIAGE BOLT

FOR 4" SETTING

 

2004 CCB - 4" Setting

MOUNTING HARDWARE

ELASTIC STOP

MOUNTINGNUT HARDWARE

Figure 12. 4" Custom-Cut Baffle Position

2004 CCB

Figure 9. Custom-Cut Baffle

12

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model SW 2004Remember Your Mower is only AS Safe AS the Operator Table of Contents Model SW Table of Contents General Information IntroductionDirection Reference Servicing the EngineISO Symbols CE Mark Fast Slow General Safety Information Safety InformationBefore Operation Considerations Before Operation Considerations Contd Rotating Blades Operation ConsiderationsMaintenance and Storage Operation Considerations ContdMaintenance and Storage Contd Mower OperationCutter Deck Belt Adjustments Mower Operation ContdDrive Control Adjustments Cutter Deck AdjustmentsCutter Deck Belt Adjustments Contd Transmission Drive BeltCutter Deck Adjustments Contd Blade Height AdjustmentCutter Blades CUSTOM-CUT Baffle Adjustment To Adjust the CUSTOM-CUT Baffle HeightEngine AIR Cleaner Cleaning the MachineChecking Engine Crankcase OIL Level Changing Engine Crankcase OILLubrication & Maintenance Troubleshooting Cutting Conditions Condition Cause CureUneven Cut on Flat Ground Wavy High-LowAppearance Scalloped Cut, or Rough ContourScalping Blades Hitting Dirt or Cutting Very Close toGround Step CutTechnical Specifications ModelsEngine Engine DeckTechnical Specifications Cont Additional Specifications Optional ITEMS/ATTACHMENTSApproximate Dimensions SWM36A SWM48A SWM52A SWM61A Cutter Decks32 & 36A Cutter Decks Ref. Part No. Number Description 32 36A 48A, 52A Cutter Decks Part Description 48A 52A Page Caster Assembly Part 36A Description 48A 52AEngine Deck Part Handle Assembly 15KH 15KA 18HN Instrument Panel Part 15KH 15KA 18HN Description 18KH 17KAFor Reference Only Order Parts from Peerless / Tecumseh DescriptionHandle Wire Harness Manual Start Wire Harness Adapter Honda 18 HP Wire Harness Adapter482284 48314 482286 482816481122 32 48315 36 482297 48 481953 52 48404Install Belt Cover Before Operating MachineLimited Warranty Commercial Equipment Garantía Limitada Equipo Comercial SWM61A SWM52A SWM48A SWM36A Aproximadas Dimensiones Continuación Técnicas EspecificacionesOpcionales ARTÍCULOS/ACCESORIOS Adicionales EspecificacionesTécnicas Especificaciones Motor DEL PlataformaMotor ModelosCorte DE Condiciones LAS EN Fallas DE Identificación Solución Causa CondiciónLa de ancho lo a Inclinadas SalientesIrregular perfil o Volado corte onduladaCorte de trayectorias Pasadas entre entre cortar sin céspedDe Franjas Vetas La en cortar sin céspedMantenimiento Y Lubricación Máquina LA DE Limpieza DEL Aceite DE Filtro DE CambioPersonalizado Corte DE Deflector DEL Ajuste DEL Altura LA Ajustar ParaPersonalizado Personalizado Corte DE DeflectorCorte DE Altura LA DE Ajuste Corte DE CuchillasContinuación Corte DE Plataforma LA DE Ajustes Corte DE Plataforma LA DE AjustesMotriz Control DE Ajustes Continuación Corte DE Plataforma LA DE Correa LA DE AjustesLA DE Correa LA DE Ajustes NotaContinuación Cortacésped DEL Operación Encendido del llave la quite y motor el DetengaCortacésped DEL Operación Continuación Almacenamiento Y MantenimientoAlmacenamiento Continuación Operación DE ConsideracionesGiratorias Cuchillas DE ConsideracionesContinuación Operación LA a Previas Consideraciones Advertencia Operador el si motor el apaga sistema El .neutralEn transmisión la desconectada, esté plataforma De sistema un con equipada está máquina EstaSeguridad DE Información OperaciónLA a Previas Consideraciones Seguridad DE General InformaciónDescripción Símbolo ISO Símbolos General Información Motor AL ServicioInstrucciones DE Referencia Scag POR Aprobados Aditamentos Y AccesoriosTema Contenido DE TablaPágina SW Modelo Página TemaOperador RecuerdeGraves Lesiones EN Resultar Puede Operación DE Seguras Prácticas LAS DE Incumplimiento ELEquipment Power Scag UU.EE EN Impreso 2004 Julio EN Impreso 03145 .No Parte
Top Page Image Contents