Scag Power Equipment STT61V-25CH-LP Safety Interlock System, Initial Run-In Procedures

Page 17

Section 4

R

6.Hourmeter (Figure 4-1). Indicates the number of hours the engine has been operated. It only operates when the engine is running. Has preset maintenance reminders for engine and hydraulic system oil changes. Will start flashing scheduled maintenance 2 hours before preset time and continue flashing until 2 hours after. Automatically resets.

7.Fuse Holders (Figure 4-1). There are two 20 amp fuses that protect the mower's electrical system. To replace fuses, pull fuse out of the socket and install a new fuse.

8.Left Steering Control (Figure 4-1). Used to control the mower's left wheel when traveling forward or reverse.

9.Right Steering Control (Figure 4-1). Used to control the mower's right wheel when traveling forward or reverse.

10.Parking Brake Control (Figure 4-1). Used to engage and disengage the parking brakes. Pull the lever back to engage the parking brakes. Push the lever forward to disengage the parking brakes.

11.Dump Valve Control Levers (Figure 4-2). Located on the hydraulic pumps, used to “free-wheel” the mower. Rotating the levers clockwise until they stop allows the unit to move under hydraulic power. The levers must be in this position and torqued to 10 lb-ft during operation of the mower. Rotating the levers counter-clockwise allows the mower to be moved by hand (free-wheeling).

DUMP VALVE

CONTROL

390S141-1

Figure 4-2. Dump Valve Control

12.Deck Lift Foot Lever (Figure 4-1). Used to raise and lower the cutter deck. Push full forward to lock in the transport position.

13.Cutting Height Adjustment (Figure 4-1). Used to set the cutter deck at the desired cutting height.

14.Deck Release Lever (Figure 4-1). Used to lock the cutter deck in the transport position. Push the foot pedal forward and pull back on the release lever to release the cutter deck for normal mowing.

15.Seat Belt (Figure 4-1).Used to secure the operator. Seat belt must be worn at all times when the ROPS is in the upright and locked position.

16.Seat Hold Down Release Latch (Figure 4-1). Located behind the seat. Used to secure the seat in the operator's position. Release the latch to gain access under the seat.

4.2 Safety Interlock System

The mower is equipped with a safety interlock system that prevents the engine from starting unless the deck drive is disengaged, the parking brake is engaged, the steering control levers are in the neutral position and the operator is in the seat. The interlock system shuts off the engine if the operator leaves the seat with the steering control levers not in the neutral position and/or the cutter blades engaged and the parking brake not engaged.

WARNING

Never operate the mower with the interlock system disconnected or malfunctioning. Do not disengage or bypass any switch; injury to yourself and others or property damage could result.

4.3 Initial Run-In Procedures

First Day of Use or Approximately 20 Hours

1.Check all belts for proper alignment and wear at 2, 4 and 8 hours.

2.Change the engine oil and oil filter after the first 20 hours of operation. (See Section 7.4.)

3.Check hydraulic oil level in reservoir. (See Section 7.3.)

4.Check for loose hardware. Tighten as needed.

5.Check interlock system for proper operation. (See Section 4.2.)

6.Check tire pressure. Adjust pressure if necessary. (See Section 7.10.)

13

Image 17
Contents OPERATOR’S Manual STT61V-25CH-LP Remember Your Mower is only AS Safe AS the OperatorTable of Contents Inside Back Cover Troubleshooting Cutting Conditions AdjustmentsIntroduction General InformationDirection Reference Servicing The Engine And Drive Train ComponentsSymbol Description SymbolsBefore Operation Considerations Safety InformationSignal Words Operation Considerations Know the function of all controls and how to stop quicklySection Foldable Roll-Over Protection System Roll-Over Protection SystemSeat Belt Inspection SPARK Ignition System Maintenance Considerations & StorageUsing a spark arrestor Section Power Head SpecificationsEngine ElectricalCutter Deck Weights And Dimensions 52V 61VHydraulic System Productivity 52V 61VControls And Instrument Identification Operating InstructionsInitial Run-In Procedures Safety Interlock SystemForward Travel Starting The EngineGround Travel And Steering Reverse Travel Engaging The Deck Drive Cutter BladesHillside Operation Rotating BladesParking The Mower After OperationRecommendations For Mowing Adjusting Cutting HeightMoving Mower With Engine Stopped Adjusting The Height Adjust Pedal Adjusting The Steering LeversTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsTracking Adjustment Throttle Control and Choke AdjustmentsCutter Deck Pitch Cutter Deck LevelCutter Deck Height Cutter Deck Height AdjustmentCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilCleaning and/or Replacing Air Cleaner Element Engine Air CleanerBattery Jump Starting Charging the BatteryDrive Belts Cutter Blades Blade ReplacementBlade Inspection Blade SharpeningChecking Lubricant Level Cutter Deck GearboxTires Changing Lubricant Body, Deck, And UpholsteryScag Approved Attachments and Accessories Illustrated Parts ListSection Section Description 52V Cutter DeckSection 61V Cutter Deck 461863 Cutter Deck Velocity Plus Cutter Deck Controls 481764 Link, Deck Lift Sheet Metal Components 9278 STT ROLL-OVER Protection System STT ROLL-OVER Protection System STT Suspension Seat Section Deck Drive Components Bolt, Hex Head 3/8-16 x Engine and Attaching Parts Kohler LP Available through the individual engine manufacturer Brake and Steering Components Bolt, Carriage 5/16-18 x Hydraulic System Kohler LP Base LP System Kohler Available through the individual engine manufacturer BDP-16A Hydraulic Pump Assembly BDP-16A Hydraulic Pump Assembly Electrical System Kohler LP Electrical System Kohler LP Heavy-Duty Replacement Decals and Information Plates Electrical Schematic Kohler LP Limited Warranty Commercial Equipment

STT61V-25CH-LP, STT52V-25CH-LP specifications

Scag Power Equipment has long been synonymous with durability and performance in the lawn care industry, and their STT52V-25CH-LP and STT61V-25CH-LP mowers exemplify this commitment. Both models are part of the Scag Turf Tiger II series, designed for commercial landscapers and serious homeowners who demand the best in cutting efficiency and reliability.

The STT52V-25CH-LP features a 52-inch cutting deck, while the STT61V-25CH-LP boasts a 61-inch deck, allowing users to choose according to the size of their lawn or landscape maintenance requirements. The decks are constructed from high-strength steel, ensuring longer life and resistance to wear from heavy use. The signature Velocity Plus deck design enhances airflow for superior cutting quality, resulting in cleaner cuts and better grass dispersal.

Powered by a robust 25 HP Kohler Command Pro engine, both models deliver the necessary power to tackle tough mowing jobs with ease. The engine's exceptional torque and performance ensure that even thick grass doesn't slow these machines down. Additionally, the Kohler engine is designed for improved fuel efficiency, helping operators save on fuel costs during long hours of operation.

One of the standout features of the STT52V-25CH-LP and STT61V-25CH-LP is their advanced hydrostatic transmission, providing smooth and responsive speed control. Operators can effortlessly adjust their speed and direction, making it easy to navigate tight spaces and uneven terrain. The ergonomic operator platform enhances comfort, with padded seats and adjustable armrests allowing for extended periods of mowing without fatigue.

Both models come equipped with a heavy-duty, commercial-grade transmission, capable of withstanding the rigors of daily use in demanding conditions. Additionally, they feature an intuitive control panel, allowing users to easily monitor important metrics, such as fuel levels and hour meters.

For added convenience, these mowers incorporate an easy-access maintenance design, allowing for quick inspections and routine servicing. With a focus on user-friendliness, Scag has ensured that operators can maintain their equipment with minimal downtime.

In summary, the STT52V-25CH-LP and STT61V-25CH-LP from Scag Power Equipment offer a compelling combination of power, performance, and user-friendly features. Ideal for commercial landscapers and serious gardening enthusiasts alike, these mowers stand ready to deliver exceptional results in any mowing environment.