Scag Power Equipment STT61V-25KBD-SS manual Tires, Blade Sharpening, Blade Replacement

Page 41

Section 7

R

B. Blade Sharpening

- NOTE -

If possible, use a file to sharpen the blade. Using a wheel grinder may burn the blade.

- NOTE -

DO NOT sharpen the blades beyond 1/3 of the width of the blade. See Figure 7-6.

1.Sharpen the cutting edge at the same bevel as the original. Sharpen only the top of the cutting edge to maintain sharpness. See Figure 7-6.

Angle Blade Back

Do Not Cut In

 

X Must NOT Exceed

30

1/3 Blade Width

SGB033

 

Figure 7-6. Blade Sharpening

2.Check the balance of the blade. If the blades are out of balance, vibration and premature wear can occur. See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades.

C. Blade Replacement

WARNING

Always wear proper hand and eye protection when working with cutter blades.

1.Remove the ignition key before replacing the blades.

2.Raise the mower deck to the highest position. Place the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.

3.Secure the cutter blades to prevent them from rotating, (use the optional Blade Buddy tool P/N 9212, to assist in securing the cutter blades), remove the nut from the blade attaching bolt. Remove the cutter blade, bolt and spacer from the spindle shaft. See Figure 7-7.

- NOTE -

The front of the machine will have to be raised slightly to remove the blade bolt from the cutter spindle.

4.To install the new cutter blade, put the flat washer onto the blade bolt and slide the bolt into the hole in the cutter blade.

HEx NUT-TORqUE

TO 75 LB-FT

SPINDLE

CUTTER

SHAFT

DECK

 

HEx HEAD

BOLT / NUT

SPINDLE

ASSEMBLY

CUTTER BLADE

SPACER

CUTTER

BLADE

WASHER

HEx HEAD BOLT

390S0160

 

 

Figure 7-7. Blade Replacement

- NOTE -

Be sure that the blade is installed with the lift wing toward the top.

5.Install the spacer onto the blade bolt and insert the bolt into the cutter spindle shaft.

6.Install the hex nut to the blade bolt at the top of the cutter spindle. Secure the blades from rotating and torque to 75 lb-ft. See Figure 7-7.

7.10 Tires

Check the tire pressures after every 8 hours of operation or daily.

Caster Wheels

Flat Free

Drive Wheels

12 PSI

37

Image 41
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Inside Back Cover AdjustmentsIntroduction General InformationDirection Reference Servicing The Engine And Drive Train ComponentsSymbol Description SymbolsBefore Operation considerations Safety InformationSignal Words Operation Considerations Section Foldable Roll-Over Protection System Roll-over protection systemSeat Belt Inspection Maintenance Considerations & storage Safety And Instructional Decals Install Belt COvER Before Power Head SpecificationsEngine ElectricalCutter Deck Weights And DimensionsHydraulic System ProductivityControls And Instrument Identification Operating InstructionsInitial Run-In Procedures Safety Interlock SystemForward Travel Starting The EngineGround Travel And Steering Reverse Travel Engaging The Deck Drive Cutter BladesParking The Mower Hillside OperationAfter Operation Removing Clogged MaterialRecommendations For Mowing Adjusting Cutting HeightMoving Mower With Engine Stopped Adjusting The Steering Levers Adjusting The Height Adjust PedalTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsTracking Adjustment Throttle Control And Choke AdjustmentsBelt Adjustment Belt Alignment Cutter Deck AdjustmentsCutter Deck Level Cutter Deck PitchCutter Deck Height Cutter Deck Height AdjustmentPosition Custom-Cut Baffle Adjustment current Production Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment early models Position Custom-Cut Baffle Adjustment Maintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilBattery Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Replacing In-Line Fuel Filter ElementsDrive Belts Charging the BatteryCutter Blades Blade InspectionBlade Sharpening Blade ReplacementTires Cooling System Cutter Deck GearboxChecking Lubricant Level Changing LubricantChecking The Fan Belt Tension Cleaning the Radiator Debris ScreenBody, Deck, And Upholstery Section Scag Approved Attachments And Accessories Illustrated Parts List61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Flatwasher, 3/8 .391 x .938 x STT ROLL-OVER Protection System with Suspension Seat STT ROLL-OVER Protection System with Suspension Seat Deck Drive Components Belt Guard, Rear Hinge, Belt Guard 481309 Latch, Hood 482433 Engine & Attaching Parts Kubota Diesel Available through the individual engine manufacturer Brake and Steering Components 48114-04 Grease Fitting 461082 Fuel and Hydraulic System Kubota Diesel Clamp, Hose BDP-16A Hydraulic Pump Assembly with Cooling FAN HG70924 Charge Pump Kit .19 STD. Splined HG51457 Electrical System Kubota Diesel 483643 Cover, Sealed Single 483641 Heavy-Duty Commercial 483158 Decal, Rops 483425 Spanish Decal Kit, STT not shown Electrical Schematic Kubota Diesel Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Del desechos de criba la de Limpieza .B VentiladorRadiador Lubricante de Cambio .B Advertencia Refrigeración DE SistemaLlantas LA DE Cambios DE CajaTransmisión DE Correas Cuchilla la de Inspección .ACorte DE Cuchillas Advertencia Batería Puente por Arranque .CBatería la de Carga .B Línea en combustible Aire de filtro Del elemento del reemplazo y/o Limpieza .ADe filtro del elementos los de Reemplazo .B Combustible de tanque del Llenado .AHidráulico aceite de filtro del elemento del Cambio .C Motor del aceite de filtro de Cambio .CCárter del aceite de Cambio .B Hidráulico aceite de Cambio .B NotaConexión de puntos de Lubricación 1-7 Figura Grasa DE Conexión DE Lubricación DE Tabla Lubricación 36 Página 1,-7 Figura LA VEARecomendados Servicio DE Intervalos Mantenimiento DE Tabla MantenimientoDe personalizado Personalizado corte de deflector del Ajuste Corte de plataforma la de Nivel Corte de plataforma la de InclinaciónAlineación de Ajuste Correa LA DE AlineaciónAdvertencia Correa LA DE Ajuste Neutral Ajuste Desplazamiento DE Ajustes AjustesSolución Causa Condición Trayectoria la de ancho Corte deLo a inclinadas Salientes IrregularDe trayectorias entre CorteCortar sin césped De Franjas VetasAltura de ajuste de pedal del Ajuste Cuestas en remolque Nunca Opcional enganche de accesorio RemolqueDetenido Motor EL CON Cortacésped DEL Desplazamiento AdvertenciaOperación LA DE Después Cuesta UNA EN OperaciónCorte DE Cuchillas Plataforma DE Transmisión LA DE Conexión Motor DEL Arranque Adelante hacia DesplazamientoPlataforma de elevación de pie de Palanca Seguridad DE Bloqueo DE SistemaInstrumentos e Controles 1-4 Figura Instrumentos E Controles DE IdentificaciónProductividad Dimensiones y PesosHidráulico Sistema Corte DE PlataformaMotor TractorEléctrico Sistema Seguridad DE Y Instructivas Calcomanías Reversa AdelanteDE Consideraciones Almacenamiento Y MantenimientoFigura Vuelco contra protección de plegable Sistema 1-2 Figura Vuelco Contra Protección DE SistemaContinuación Nota Operación DE ConsideracionesSeñalización DE Palabras Operar DE Antes ConsideracionesLento Rápido Símbolos Introducción 1.1 General Información Instrucciones DE ReferenciaContinuación Contenido DE Tabla Contenido DE Tabla Advertencia Manual

STT61V-25KBD-SS specifications

Scag Power Equipment has long been recognized for its durable, high-performance lawn care machines, and the STT61V-25KBD-SS is no exception. This commercial-grade lawn mower is designed to meet the demanding needs of professional landscapers and homeowners alike, offering unmatched efficiency, comfort, and cutting quality.

At the heart of the STT61V-25KBD-SS is a robust 25 horsepower Kawasaki engine, known for its reliability and outstanding power delivery. This powerhouse enables the mower to navigate through tough grass and varied terrains seamlessly, ensuring that no job is too big or challenging. The engine’s performance is complemented by a hydrostatic drive system, which provides smooth and responsive operation without the need for gear shifting, allowing operators to focus on their mowing task without interruption.

One of the standout features of the STT61V-25KBD-SS is its 61-inch Velocity Plus cutting deck. This innovative deck design promotes superior airflow, resulting in an exceptional cut quality and a clean discharge of clippings. The three-blade system allows for versatile cutting options, making it suitable for both residential lawns and commercial properties. Users will appreciate the adjustable cutting height, which offers a range between 1 inch and 4.5 inches to accommodate various grass types and conditions.

In addition to its cutting prowess, the STT61V-25KBD-SS prioritizes operator comfort and convenience. It features a comfortable seat with cushioning and armrests, providing support during long hours of operation. The ergonomic controls ensure easy maneuverability, allowing operators to navigate efficiently around obstacles.

Durability is another hallmark of Scag Power Equipment, and the STT61V-25KBD-SS is no exception. Its heavy-duty steel frame and components are engineered to withstand the rigors of commercial use, ensuring longevity and reliability. The mower's easy-to-access maintenance points simplify routine servicing, further enhancing its practicality.

Overall, the Scag Power Equipment STT61V-25KBD-SS is a powerful, versatile, and durable mower that stands out in the commercial lawn care market. With its impressive engine, advanced cutting deck technology, and operator-focused design, it represents an excellent investment for anyone serious about maintaining pristine lawns. Whether for professional landscaping or personal use, this mower delivers exceptional results time and time again.