Scag Power Equipment STT61V-25KBD-SS manual Engaging The Deck Drive Cutter Blades, Reverse Travel

Page 19

Section 4

R

Reverse Travel

Caution

Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.

4.6Engaging The Deck Drive (Cutter Blades)

1.Set the throttle at about 3/4 speed. Do not attempt to engage the deck drive at high speed as this shortens the electric clutch life — use only moderate engine speed when engaging the deck drive.

2.Engage the deck drive by pulling out on the yellow switch, located on the instrument panel, to the engage position. See Figure 4-3.

Caution

Before backing up, observe the rear for persons and obstructions. Clear the area before backing up. Possible injury or property damage could occur.

To travel in reverse, pull both handles back. Keep the travel speed low while traveling in reverse.

- NOTE -

The mower may not travel straight in reverse. Slight adjustments may need to be made using the steering controls.

To steer left while traveling in reverse, allow the left steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn left.

To steer right while traveling in reverse, allow the right steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn right.

To stop the reverse travel, allow the steering control levers to return to the neutral position. If the mower is to be parked, engage the parking brake.

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

390S013

Figure 4-3. Cutter Engage Switch

- NOTE -

A squealing noise may be heard when engaging or disengaging the deck drive. It is caused by the electric clutch plates meshing as the mower comes up to speed.

3.To disengage the deck drive, push the switch in to the disengage position.

4.Always operate the engine at full throttle to properly maintain cutting speed. If the engine starts to lug down, reduce the forward speed and allow the engine to operate at maximum RPM.

15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Inside Back Cover AdjustmentsServicing The Engine And Drive Train Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsSignal Words Safety InformationBefore Operation considerations Operation Considerations Section Foldable Roll-Over Protection System Roll-over protection systemSeat Belt Inspection Maintenance Considerations & storage Safety And Instructional Decals Install Belt COvER Before Electrical SpecificationsPower Head EngineProductivity Weights And DimensionsCutter Deck Hydraulic SystemControls And Instrument Identification Operating InstructionsInitial Run-In Procedures Safety Interlock SystemGround Travel And Steering Starting The EngineForward Travel Reverse Travel Engaging The Deck Drive Cutter BladesRemoving Clogged Material Hillside OperationParking The Mower After OperationMoving Mower With Engine Stopped Adjusting Cutting HeightRecommendations For Mowing Adjusting The Steering Levers Adjusting The Height Adjust PedalTowing Optional Hitch Accessory Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Adjustment Throttle Control And Choke AdjustmentsTracking Adjustment Cutter Deck Pitch Cutter Deck AdjustmentsBelt Alignment Cutter Deck LevelCutter Deck Height Cutter Deck Height AdjustmentPosition Custom-Cut Baffle Adjustment early models Custom-Cut Baffle AdjustmentPosition Custom-Cut Baffle Adjustment current Production Position Custom-Cut Baffle Adjustment Maintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OilReplacing In-Line Fuel Filter Elements Engine Air CleanerBattery Cleaning and/or Replacing Air Cleaner ElementBlade Inspection Charging the BatteryDrive Belts Cutter BladesTires Blade ReplacementBlade Sharpening Changing Lubricant Cutter Deck GearboxCooling System Checking Lubricant LevelBody, Deck, And Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Section Scag Approved Attachments And Accessories Illustrated Parts List61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Flatwasher, 3/8 .391 x .938 x STT ROLL-OVER Protection System with Suspension Seat STT ROLL-OVER Protection System with Suspension Seat Deck Drive Components Belt Guard, Rear Hinge, Belt Guard 481309 Latch, Hood 482433 Engine & Attaching Parts Kubota Diesel Available through the individual engine manufacturer Brake and Steering Components 48114-04 Grease Fitting 461082 Fuel and Hydraulic System Kubota Diesel Clamp, Hose BDP-16A Hydraulic Pump Assembly with Cooling FAN HG70924 Charge Pump Kit .19 STD. Splined HG51457 Electrical System Kubota Diesel 483643 Cover, Sealed Single 483641 Heavy-Duty Commercial 483158 Decal, Rops 483425 Spanish Decal Kit, STT not shown Electrical Schematic Kubota Diesel Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Radiador VentiladorDel desechos de criba la de Limpieza .B Lubricante de Cambio .B Advertencia Refrigeración DE SistemaLlantas LA DE Cambios DE CajaCorte DE Cuchillas Cuchilla la de Inspección .ATransmisión DE Correas Batería la de Carga .B Puente por Arranque .CAdvertencia Batería Combustible de tanque del Llenado .A Aire de filtro Del elemento del reemplazo y/o Limpieza .ALínea en combustible De filtro del elementos los de Reemplazo .BCárter del aceite de Cambio .B Motor del aceite de filtro de Cambio .CHidráulico aceite de filtro del elemento del Cambio .C Hidráulico aceite de Cambio .B NotaConexión de puntos de Lubricación 1-7 Figura Grasa DE Conexión DE Lubricación DE Tabla Lubricación 36 Página 1,-7 Figura LA VEARecomendados Servicio DE Intervalos Mantenimiento DE Tabla MantenimientoDe personalizado Personalizado corte de deflector del Ajuste Corte de plataforma la de Nivel Corte de plataforma la de InclinaciónAdvertencia Correa LA DE Ajuste Correa LA DE AlineaciónAlineación de Ajuste Neutral Ajuste Desplazamiento DE Ajustes AjustesSolución Causa Condición Irregular Corte deTrayectoria la de ancho Lo a inclinadas SalientesDe Franjas Vetas CorteDe trayectorias entre Cortar sin céspedAltura de ajuste de pedal del Ajuste Cuestas en remolque Nunca Opcional enganche de accesorio RemolqueDetenido Motor EL CON Cortacésped DEL Desplazamiento AdvertenciaOperación LA DE Después Cuesta UNA EN OperaciónCorte DE Cuchillas Plataforma DE Transmisión LA DE Conexión Motor DEL Arranque Adelante hacia DesplazamientoPlataforma de elevación de pie de Palanca Seguridad DE Bloqueo DE SistemaInstrumentos e Controles 1-4 Figura Instrumentos E Controles DE IdentificaciónCorte DE Plataforma Dimensiones y PesosProductividad Hidráulico SistemaEléctrico Sistema TractorMotor Seguridad DE Y Instructivas Calcomanías Reversa AdelanteDE Consideraciones Almacenamiento Y MantenimientoFigura Vuelco contra protección de plegable Sistema 1-2 Figura Vuelco Contra Protección DE SistemaContinuación Nota Operación DE ConsideracionesSeñalización DE Palabras Operar DE Antes ConsideracionesLento Rápido Símbolos Introducción 1.1 General Información Instrucciones DE ReferenciaContinuación Contenido DE Tabla Contenido DE Tabla Advertencia Manual

STT61V-25KBD-SS specifications

Scag Power Equipment has long been recognized for its durable, high-performance lawn care machines, and the STT61V-25KBD-SS is no exception. This commercial-grade lawn mower is designed to meet the demanding needs of professional landscapers and homeowners alike, offering unmatched efficiency, comfort, and cutting quality.

At the heart of the STT61V-25KBD-SS is a robust 25 horsepower Kawasaki engine, known for its reliability and outstanding power delivery. This powerhouse enables the mower to navigate through tough grass and varied terrains seamlessly, ensuring that no job is too big or challenging. The engine’s performance is complemented by a hydrostatic drive system, which provides smooth and responsive operation without the need for gear shifting, allowing operators to focus on their mowing task without interruption.

One of the standout features of the STT61V-25KBD-SS is its 61-inch Velocity Plus cutting deck. This innovative deck design promotes superior airflow, resulting in an exceptional cut quality and a clean discharge of clippings. The three-blade system allows for versatile cutting options, making it suitable for both residential lawns and commercial properties. Users will appreciate the adjustable cutting height, which offers a range between 1 inch and 4.5 inches to accommodate various grass types and conditions.

In addition to its cutting prowess, the STT61V-25KBD-SS prioritizes operator comfort and convenience. It features a comfortable seat with cushioning and armrests, providing support during long hours of operation. The ergonomic controls ensure easy maneuverability, allowing operators to navigate efficiently around obstacles.

Durability is another hallmark of Scag Power Equipment, and the STT61V-25KBD-SS is no exception. Its heavy-duty steel frame and components are engineered to withstand the rigors of commercial use, ensuring longevity and reliability. The mower's easy-to-access maintenance points simplify routine servicing, further enhancing its practicality.

Overall, the Scag Power Equipment STT61V-25KBD-SS is a powerful, versatile, and durable mower that stands out in the commercial lawn care market. With its impressive engine, advanced cutting deck technology, and operator-focused design, it represents an excellent investment for anyone serious about maintaining pristine lawns. Whether for professional landscaping or personal use, this mower delivers exceptional results time and time again.
Top Page Image Contents