Quantum Data 802 quick start Serial Port Configuration, Set Gpib Address, Set Baud rate to

Page 9

Power-up Modes

Serial Port Configuration

The default setting of the RS-232 serial port is 2400 Baud, No Parity, 8 data bits, 1 Stop bit, No Handshaking (2400, N, 8, 1, N, N) and normal programming language support. The following special modes can be activated by holding down the indi- cated buttons on power up and will be retained when the unit is turned off.

Set Baud rate to 9600

Image

 

 

 

V ideo Gate

 

 

 

 

 

Sync Gate

 

 

 

Outputs

 

STEP

R

 

G

B

 

 

 

ACS

 

DCS

DSS

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enables normal programming lan- guage support at 9600 Baud.

Enable numeric keypad

Image

 

 

 

V ideo Gate

 

 

 

 

 

Sync Gate

 

 

 

Outputs

 

STEP

R

 

G

B

 

 

 

ACS

 

DCS

DSS

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Switches protocol to support an optional Model 8020 numeric keypad.

Enable programmable keypad

 

Image

 

 

V ideo Gate

 

 

 

Sync Gate

 

 

Outputs

 

STEP

R

 

G

B

 

ACS

 

DCS

DSS

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Switches protocol to support an optional 35 key programmable key- pad.

Set GPIB Address

Generators that have the GPIB (IEEE-

488)port option installed use two rotary switches for setting the GPIB address. These switches are acces- sible through the ventilation slots as shown here.

The generator stores its current GPIB address in nonvolatile memory. A normal power-up will not update the memory to any new switch settings. The GPIB address is normally read from the switches into memory by holding down the indicated button on power up.

Image

 

 

 

V ideo Gate

 

 

 

 

 

Sync Gate

 

 

 

Outputs

 

STEP

R

 

G

B

 

 

 

ACS

 

DCS

DSS

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes:

The current GPIB address is stored in system memory and displayed during power-up.

The GPIB address switches are also read into memory if the generator goes through a full re-initialization for any reason.

The IEEE-488 configuration descrip- tion of the generator is:

SH1AH1T6TEØLEØSR1RL1PPØDC1DT1CØ

Model 802 Series Quick Start Guide

• 9 •

Image 9
Contents Model 802 Series USB Gpib Making ConnectionsDVI Connector Pinout Chart DVI Options Only Lvds Connector Pinout Chart Lvds Option OnlyVideo Connector Pinout Diagram Units with TV option Only LCD Window Information Front Panel Controls and Indicators Normal ModeOverview Special Operating Modes and FunctionsInitialize w/Factory Defaults Power up ModesRemove All Modes Use Old Format NamesPower-up Modes Digital Friendly ModeAnalog Friendly Mode Clone Must be exact same model and firmware Enable numeric keypad Serial Port ConfigurationEnable programmable keypad Set Gpib AddressCalibrate Enable Status DisplayToggle Analog / Digital Video Type Special Key FunctionsRotate Video Color Type Set Pixel DepthDDC Based Autoconfiguration Test Method High-bandwidth Digital Copy Protection Hdcp TestingVideo Generator Manager VGM Using a Computer for Control and ProgrammingVGM Image Editor VGM Format EditorVGM Sequence Player VGM Sequence EditorInstructions for Bitmap Picture Download Using a Computer for Control and Programming Advanced Programming Methods Updating Generator Firmware802B, 802F, 802G Quantum Data, Inc Big Timber Rd Elgin, IL