Trouble-Shooting

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check the power cord. The power cord must be plugged into a grounded outlet (see PLUG- GING IN THE RESTORATION 2.0 on page 10).

b.Check to see if the GFCI breaker is tripped, or was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR GFCI BREAKER TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker. If the circuit breaker trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter housing from the spa jet unit and clean or replace the filter.

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

c.The pump may have a loose wire connection. Contact our customer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

4.SYMPTOM: THE PUMP HUMS BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

b. The pump may have a bad bearing. Contact our customer service department or, if your spa is no longer under warranty, you may also con- tact a local spa and pool service provider.

6.SYMPTOM: THE WATER DOES NOT HEAT

a.The pump in the spa jet unit is the heater. If the pump is operating, the water should heat. Cover the RESTORATION 2.0 with the spa cover. The spa cover must be tight with the insulation blanket in place. Set the air control to low. The water will heat at a rate of 2.0¡F an hour. If you are using the spa indoors, and the room temperature is maintained at 70¡F, it will take approximately 18 to 24 hours for the water to reach the set temperature.

b.If you are using the RESTORATION 2.0 out- doors, it may take longer for the water to heat. See the chart below for the approximate heat- ing time.

Air Temperature	Heating Time
70¡F +	18 to 24 hours
50¡FÐ70¡F	24 to 48 hours
30¡FÐ50¡F	48 to 72 hours

b. If the water still has not heated after four days, contact our customer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider. Note: When the air temperature is below 30¡F, the heater will not be able to maintain the maximum set temperature.

7.SYMPTOM: THE SPA CONTINUES TO RUN AFTER IT HAS BEEN SHUT OFF

a.To turn the spa jets on, press the ON/OFF con- trol once. To turn the spa jets off, press the control again. After you press it once, the spa jets will shut off for about 30 seconds, and restart. Press the control again. The spa jets will remain off for 20 minutes, at which time they will begin running the filter cycle. At any time after the spa jets has been shut off, the pump will begin cycling the water if the temper- ature falls below the minimum setting.

PFHS70071 specifications

The ProForm PFHS70071 is a cutting-edge piece of fitness equipment designed for those who are serious about their workout routines. This treadmill incorporates advanced technology and a host of features aimed at enhancing user experience and overall effectiveness of workouts.

One of the standout features of the PFHS70071 is its powerful motor, capable of sustaining speeds of up to 12 miles per hour. This allows users to engage in intense running sessions or a gentle walk, making it suitable for all fitness levels. The running surface is spacious, offering ample room for comfortable strides at various speeds.

The treadmill also includes an impressive incline capability of up to 15%. This feature simulates uphill running, significantly increasing workout intensity and helping users build muscle while burning more calories. The digital LED display provides real-time data on important metrics, including distance traveled, speed, time, and calories burned, helping users monitor their progress effectively.

One of the key technologies incorporated in the PFHS70071 is the iFit compatibility. This allows users to access a wide variety of on-demand workouts led by professional trainers. Users can explore numerous routes and landscapes, thanks to the Google Maps integration, which adapts the incline of the treadmill to match the terrain of their selected route. This function keeps workouts fresh and engaging, offering almost limitless workout options.

The ProForm PFHS70071 is also designed with comfort in mind. The treadmill features ProShox cushioning technology, which reduces impact on joints and provides a more comfortable running experience. This is especially beneficial for those who may be prone to injuries or are recovering from them.

Safety is addressed through an emergency stop feature and a spacious safety zone, ensuring that users can exercise without worries. Additionally, the built-in Bluetooth speakers allow users to enjoy their favorite music or podcasts, making workouts more enjoyable.

In summary, the ProForm PFHS70071 treadmill combines power, technology, and user-friendly features to create a versatile fitness experience. It is designed to cater to various workout preferences, making it an ideal choice for both beginners and seasoned athletes looking to enhance their training routine. Whether you're running, walking, or utilizing the innovative iFit program, this treadmill offers a comprehensive solution to meet fitness goals and encourage a healthier lifestyle.