McCulloch 538E - 38 cc Chain Sharpening, Fault Finding Table, Chain Catcher, MP 370 GLX PM 320 GX

Page 12

UK

2The chain brake (A) is engaged when brake lever is in the position (chain cannot rotate).The chain brake should snap into both positions.If strong resistance is felt or lever does not move into either position, DO NOT USE YOUR SAW. Take it immediately to an authorized servicing dealer.

3CHAIN CATCHER

This unit is fitted with a chain catcher below the drive spocket. This is intended to stop the rearward movement of the chain in case of breakage or if it should come out of the bar. It should never be removed.

CHAIN SHARPENING

L

1Chain cutter teeth can be sharpened with a round file, as follows:

CHAIN

FILE

MP 370 GLX

5/32”

PM 320 GX

3/16”

The exact chain type is marked on the bottom half of the drive link which runs inside the bar groove.

Filing can be made easier by also using a file holder. The chain can remain fitted on the bar during sharpening. Before commencing, the chain should be tensioned cor- rectly and the chain brake should be activated to prevent the chain from moving.

2To obtain a correct sharpening the file must be carefully

held to maintain 3 basic angles:

 

– “A” Top angle

30° - 35°

– “B” External, side angle

85° - 90°

– “C” Internal, side angle

60°

File in one direction only, from the “inside” of the cutter tooth towards the “outside”.

Do not allow the file to touch the chain as you bring it back to re-position it. Each cutter tooth should be filed with the same number of strokes.

3The file should be held horizontally to the cutter tooth being sharpened.

4Best results to obtain a precise sideways angle can be obtained by holding the file so that it rises 0,5 mm above the top face of the cutter tooth.

5DEPTH GAUGE

Correct depth gauge height is vital to ensure maximum chain life and cutting efficiency.

The height of the depth gauge should be lowered as the cutter tooth is filed back; this height should be checked every 4 or 5 sharpenings.

The best way to do this is to use a flat file and a depth gauge tool.

The correct setting is 0.65 mm below the top edge of the cutter tooth.

The cutter tooth depth gauge should then be rounded (D).

FAULT FINDING TABLE

 

Engine will not start

Engine runs badly

The chainsaw runs

Engine runs badly or

 

 

 

but does not cut well

looses power when cutting

 

 

 

 

 

Check STOP switch

 

 

 

is in the position I.

 

 

 

 

 

 

 

 

Control fuel level

 

 

min. 25% tank capacity.

 

 

 

 

 

 

 

Check air filter is clean.

 

 

Remove spark plug,

 

 

 

 

dry it, clean it and adjust it,

 

 

and replace it, if necessary.

 

 

 

 

 

 

 

Control and adjust

 

 

 

 

the carburetor screws

 

 

if necessary.

 

 

 

 

 

 

 

Change fuel filter.

 

 

 

Contact your dealer.

 

 

 

 

 

 

 

 

Carefully follow the chain

 

 

 

assembly instructions.

 

 

 

 

 

 

 

 

Check chain is sharp.

 

 

 

Otherwise, contact your dealer.

 

 

 

 

 

 

 

 

Engine still gives trouble: contact your dealer.

5

Image 12
Contents 38 cc 40 cc 46 cc Page Partner Page Page MAC 538E Specifications Symbol Meaning Safety PrecautionsGeneral Description BARBAR and Chain Installation Intenz C Only USE Original Spare Parts and ACCESSO- RiesFuel MIX IntenzStarting and Stopping UsagefCarburettor Adjustmentg Routine MaintenanceSafety Chain Brake Fault Finding Table Chain SharpeningChain Catcher MP 370 GLX PM 320 GX000001 000001