Makita Maintenance Tips for Chainsaws: DCS 6000I & DCS 6800I

Page 27

Cleaning the air filter

2

3

1

STOP

E

-Remove the filter cover (E/1) (2 screws).

-Loosen the screws on the air filter (E/2) and remove from intake manifold.

IMPORTANT:

Cover the intake opening with a clean cloth to prevent dirt particles from getting into the carburetor.

-Clean the air intake opening (E/3) and the inside of the air filter with a suitable brush.

Replacing the spark plug STOP

1

G

CAUTION:

Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before start- ing any maintenance work.

A hot engine can cause burns. Wear protective gloves!

The spark plug must be replaced in case of damage to the insulator, electrode erosion (burn) or if the electrodes are very dirty or oily.

-Remove the filter cover (see "Cleaning the air filter" above, Fig. E/1).

-Pull the plug cap (G/1) off the spark plug. Use only the combination wrench supplied with the saw to remove the spark plug.

CAUTION: Use only the following spark plugs:

CHAMPION RCJ-6Y or NGK BPMR 7A.

F

-Pry apart the top and bottom of the air filter as shown in Figure F.

CAUTION:

To prevent injury to the eyes, do NOT blow out dirt particles!

Do not use fuel to clean the air filter.

-Clean the air filter with a soft brush.

-If the filter is very dirty, clean it in lukewarm water with dishwashing detergent.

-Let the air filter dry completely.

-Put the top and bottom sections back together.

-Before reinstalling the air filter, check the intake opening and remove any dirt particles. If there are any, remove them with a brush.

Clean frequently (several times a day) when working in very dusty or dirty conditions. Full engine power is possible only with a clean air filter!

CAUTION: If the air filter becomes damaged, replace im- mediately! Pieces of cloth or large dirt particles can de- stroy the engine!

.020" (0,5 mm)

H

Electrode gap

The electrode gap must be .020" (0.5 mm).

Checking the ignition spark

-Press the loosened spark plug with the ignition cable firmly connected against the cylinder using insulated pliers (not near the spark plug opening).

-ON/OFF switch in the "I" (ON) position.

-Pull the starter cable hard.

If the function is correct, an ignition spark must be visible near the electrodes.

27

Image 27
Contents Owner’s Safety Manual RE Y Makita DCS 6000i ContentsSymbols Delivery inventoryRecycling Additional safety precautions Safety precautions for chain saw operatorsOperator General Safety PrecautionsDiscription of symbols used on chain saws Ansi B175.1-1991Transporting the chain saw Proper clothingSaw Use of the sawFueling instructions Chain saw operating instructionsFeet FuelingImportant adjustments Working conditionsCutting instructions Reactive forces during the cut, including kickback KickbackDepth gauges Saw chain cutter sharpnessTo avoid kickback Speed of contact at which the cutter contacts the objectTo avoid pull-in Cutting techniquesPushback To avoid pushback= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodLimbing Bucking129 Maintaining and storing the saw Maintenance and RepairYear of manufacture 523.102.672 443.053.661 Denomination of components Identification plateDCS Serial noLength Pitch Technical dataApproved bar and chain combinations Models Makita DCS 6000iMounting the guide bar and saw chain StopEngaging the chain brake braking Chain brakeTightening the saw chain Checking the chain tensionHandling and storage Waste oilFuel / Refuelling Fuel mixtureLubricating the chain Adjusting the chain lubricationClean screw cap and tank after refuelling RefuellingStarting the engine Stopping the engineChecking the chain brake Checking the chain lubrication Adjusting the carburetorExcessive depth increases the risk of kickback Working in winterSharpening the saw chain 030Cleaning the guide bar Files and how to work with themProtective gloves must be worn Cleaning the brake band and sprocket interior Replacing the saw chainReplacing the suction head Electrode gap Cleaning the air filterReplacing the spark plug Stop Champion RCJ-6Y or NGK Bpmr 7AReplacing/cleaning the spark arrester screen Replacing the return spring Replacing the starter cableService, spare parts and guarantee Instructions for daily and periodic maintenanceMaintenance and repair Malfunction System Observation Cause TroubleshootingGuarantee Spare partsBar and chain combinations Canada Extract from the spare parts list DCSPage Makita U.S.A., INC Makita Canada INC

DCS 6800I, DCS 6000I specifications

The Makita DCS 6000I and DCS 6800I are two formidable chainsaw models from a brand renowned for its commitment to durability, performance, and innovation. Both saws are designed for professional users who require power, efficiency, and precision in their cutting tasks.

Starting with the DCS 6000I, it offers an impressive engine displacement of 59 cc, producing high torque and enabling effective cutting through thick wood with ease. Its lightweight design, weighing approximately 5.8 kg, ensures better maneuverability during extended use. The DCS 6000I incorporates a 20-inch guide bar, making it suitable for a variety of applications, from felling trees to milling logs.

A key feature of the DCS 6000I is its advanced anti-vibration technology, which minimizes user fatigue and enhances comfort. The model is equipped with an automatic chain lubrication system that maintains optimal performance and prolongs the lifespan of the chain. The air cleaner is easily accessible and designed to filter out debris, ensuring clean air intake and efficient engine performance.

Moving on to the DCS 6800I, it takes power to the next level, featuring a robust 66 cc engine. This model is an ideal choice for professional users involved in heavy-duty cutting tasks. Weighing approximately 6.2 kg, it strikes a balance between power and manageability. Its 24-inch guide bar makes it a perfect fit for felling larger trees and undertaking more demanding forestry work.

The DCS 6800I is characterized by its high-performance oil pump that allows for adjustable flow rates, ensuring efficient lubrication based on the cutting conditions. Additionally, this model features an innovative decompression valve, allowing for easy starting and improved user experience. The DCS 6800I also has a semi-automatic choke that enhances startup efficiency.

Both models exhibit excellent build quality, featuring magnesium components that contribute to their lightweight yet robust structure. They also come with a tool-less air filter cover, facilitating ease of maintenance. Safety is a priority with both saws, equipped with chain brakes and throttle locks to prevent accidental starts.

In summary, the Makita DCS 6000I and DCS 6800I are exceptional chainsaws that cater to the needs of professional users. With advanced technologies, durable construction, and innovative features, these models are well-suited for various applications in forestry and landscaping, ensuring reliability, efficiency, and safety in all cutting tasks.