Simplicity ZT4000 Series manual Mowing Height Adjustment, Foot Pedal Adjustment

Page 20

Operation

Mowing Height Adjustment

The cutting height adjustment pin (A, Figure 5) controls the mower cutting height. The cutting height is adjustable between 1-3/4” (4,4 cm) and 4-1/2” (11,4 cm) in 1/4” (0,64 cm) increments.

1.Depress the deck lift foot pedal (B) until it locks into the 4-1/2” (11,4 cm) position.

2.Place the cutting height adjustment pin in the desired cutting height.

3.Depress the deck lift foot pedal then push the lock lever (C) towards the right to release the lock.

4.Release the deck lift foot pedal until it comes to rest against the cutting height adjustment pin.

Foot Pedal Adjustment

The deck lift foot pedal can be adjusted to accommodate the operator’s height for optimal comfort.

To Adjust Pedal Position:

1.Remove the foot pedal (A, Figure 6) from the pedal mount tab (B).

2.Remove the pedal mount hardware (C) and rotate the tab 180 degrees.

3.Reinstall the pedal mount hardware and tighten securely.

4.Reinstall the foot pedal on the pedal mount tab in the proper orientation as shown in Figure 6.

	C
B	A
B

Figure 5. Mowing Height Adjustment

A.Cutting Height Adjustment Pin

B.Deck Lift Foot Pedal

C.Deck Lift Lock Lever

B

AC

OPTIONAL

POSITION

Figure 6. Foot Pedal Adjustment

A.Deck Lift Foot Pedal

B.Pedal Mount Tab

C.Pedal Mount Hardware

18	www.simplicitymfg.com

Image 20

Contents Mfg. No Description 5900765 24HP Zero-Turn Riders Mfg. No Description 590070726HP Zero-Turn Riders Date Purchased Table of Contents Children Operating SafetyRead the Manual Moving Parts Slope OperationThrown Objects Overhead Obstacles Roll Bar UseRetaining Walls, Drop-offs, and Water Fuel and Maintenance Enclosed AreasGeneral Operation Transporting and StorageTowed Equipment Ride-On Units EmissionsIgnition System Operating on steep slopes can be dangerousSafe Handling of Gasoline Service and MaintenanceService & Maintenance Inspection of the Roll Bar Protective Structure Roll Bar InstructionsOperational Warnings Inspection and Maintenance of the Roll Bar Seat Belt Safety Decals Objects HazardSafety Interlock System Operational Safety ChecksSafety Icons North American Safety IconsIdentification Numbers CE ModelsCE Identification Tag Markings North American ModelsChoke PTO Power Take Off SwitchParking Brake Ignition Switch Hour Meter / Maintenance ReminderSeat Adjustment Lever Throttle ControlGeneral Operating Safety Checks Before StartingSeat Adjustment Check Tire PressuresPushing the Rider by Hand OperationTo Adjust Pedal Position Mowing Height AdjustmentFoot Pedal Adjustment Starting the Engine Stopping the RiderForward Travel Practice Zero-Turn Driving PracticeSmooth Travel Practice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Storage MowingMowing Recommendations Fire or explosion can cause severe burns or deathMowing Methods Attaching a Trailer Proper MulchingMulching Requires Excellent Mowing Conditions How Much Grass to MulchMaintenance Schedule Check Rider / Mower for loose hardwareChecking / Adding Fuel Fuel FilterChange Oil & Filter Inspect Muffler and Spark ArresterChange Hydraulic Oil Filter Battery MaintenanceCheck Hydraulic Oil Level Lubrication GreaseOil Lubricating the Front CastersServicing The Mower Blades Inspecting the Mower BladesReinstalling the Mower Blades Balancing the Mower Blade NailGround Speed Control Lever Adjustment Speed Balancing AdjustmentTo Adjust Neutral AdjustmentReturn-to-Neutral Adjustment Parking Brake Adjustment Hydraulic Pump Drive Belt ReplacementSpring loaded components can kick back causing injury Rear Suspension AdjustmentTo adjust the spring pre-load Deck Lift Rod Timing And Leveling Adjustment Mower Belt Replacement Mower PTO Belt Idler Arm Stationary Idler PulleyTroubleshooting Troubleshooting the RiderTroubleshooting the Rider Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingDeck HP Briggs & StrattonHydroGear PG-3H / HGM-12E Indentification Product Quick Specs