HOW to Stop Your Unit

STo stop the engine, push and hold the STOP switch in the STOP position until the engine stops.

SIf engine does not stop, move choke to the FULL CHOKE position.

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any contact with the muffler. A hot muffler can cause serious burns.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

NOTE: Make sure approximately 3 - 4 inches (8 - 10 cm) of line is extended from the cutting head before starting unit. This will allow the line to advance properly once the unit starts.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Primer Bulb

Choke

Lever

Starter Handle

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 se- conds, then move the choke lever to the RUN position. Allow the unit to run for 30 more seconds at RUN before releasing the throttle trigger.

NOTE: If engine dies with the choke le- ver in the RUN position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 6 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to RUN.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position; then, pull the rope to clear the engine of excess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

TE475, TE475Y specifications

The Poulan TE475 and TE475Y are powerful gas-powered chainsaws designed for both professionals and avid homeowners seeking reliable performance for their cutting tasks. Built by Poulan, a brand recognized for its durable outdoor power equipment, these chainsaws are engineered to tackle a variety of cutting jobs, including tree felling, limb removal, and firewood preparation.

One of the standout features of the Poulan TE475 is its robust 47cc, 2-cycle engine, delivering a significant amount of power to handle tough cutting tasks. This engine not only provides exceptional performance but is also designed for easy starting, minimizing downtime when you need to get the job done. The TE475Y variant usually comes with similar engine specifications, ensuring consistent and reliable power output.

Both models feature a high-quality bar and chain system that allows for efficient cutting with smooth performance. The chainsaw is equipped with a 20-inch guide bar, making it ideal for cutting larger trees and branches with ease. The low-kickback chain enhances user safety while ensuring precise and clean cuts.

In terms of usability, the Poulan TE475 and TE475Y are designed with user comfort in mind. The ergonomically designed handle provides a comfortable grip, allowing for prolonged use without causing fatigue. Additionally, the vibration-reducing technology integrated into these chainsaws helps minimize operator fatigue, making them manageable during extended cutting sessions.

Safety features are also a priority in the design of these chainsaws. The automatic chain brake helps protect the user from chain backlash, activating instantly in case of kickback. The chainsaws include easy-access air filters for simple maintenance and longer engine life, ensuring that the equipment remains in top condition for longer periods.

The Poulan TE475 and TE475Y are easy to maintain, featuring a tool-less chain tensioning system that allows users to adjust the chain quickly and conveniently, ensuring optimal performance at all times. Furthermore, their lightweight design contributes to maneuverability, making them a great choice for both seasoned professionals and casual users alike.

In summary, the Poulan TE475 and TE475Y chainsaws stand out due to their powerful engines, reliable cutting performance, user-friendly design, and safety features. These chainsaws are versatile tools that can handle a variety of cutting tasks, making them an excellent investment for anyone needing high-quality outdoor power equipment. Whether you are tackling a small yard project or engaging in heavy-duty forestry work, the Poulan TE475 and TE475Y deliver the power and performance necessary to get the job done efficiently.