Poulan S31BC Replacing the Line, Blade Replacement, Carburetor Adjustment, Seasonal Storage

Page 12

REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) di- ameter Snappert/Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

 

Line in Notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for blade re- placement instructions and illustrations.

CARBURETOR ADJUSTMENT

Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an authorized service dealer. Damage will occur if you turn the needles beyond the limiter stops.

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans- porting.

SStore unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy

storage.

SStore in a clean dry area.

SLightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

SReplace your gasoline can if it starts to rust.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Manual de Instrucciones Manuel d’Instructions Operator Safety Always WearUNIT/MAINTENANCE Safety Fuel SafetyCutting Safety Transporting and StorageCarton Contents Adjust and Secure the HAN- DlebarAssembly of Shoulder Strap Tools RequiredConfiguring Your Unit Assembly Information Trimmer HeadAssembly Information Weed Blade Attaching the Plastic Shield and Trimmer HeadInstallation of the Metal Blade Attaching the Metal ShieldON/STOP Switch HOW to Stop Your UnitKnow Your Brushcutter Primer BulbHOW to Start Your Unit Starting a Warm EngineStarting a Flooded Engine Operating Position Trimmer Line Advance Operating Instructions for USE with Trimmer HeadCutting Methods Operating Instructions for USE with Weed Blade TrimmingInspect and Clean Unit and DE- Cals Clean AIR FilterCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsBlade Replacement Carburetor AdjustmentReplacing the Line Seasonal StorageTroubleshooting Table Cause Remedy Electrolux Home PRODUCTS, INC

S31BC specifications

The Poulan S31BC is a versatile and powerful piece of outdoor equipment designed to meet the demands of both homeowners and landscaping professionals. This trimmer stands out for its efficiency, durability, and user-friendly features, making it a popular choice for tackling a variety of trimming tasks.

One of the standout features of the Poulan S31BC is its robust 31cc, 2-cycle engine. This powerful engine delivers the necessary torque to handle thick underbrush and tough weeds effortlessly. The 2-cycle engine is designed for high performance while remaining lightweight, which is crucial for extended use without causing fatigue to the operator. Additionally, the engine offers easy starting technology coupled with a smooth operation, allowing for hassle-free trimming in various environments.

The design of the Poulan S31BC also embraces ergonomic principles. Its lightweight frame and adjustable handle provide optimal control and comfort, reducing strain on the user's hands and back during extended use. This trimmer is equipped with a "split-shaft" construction that allows for easy attachment changes. Users can seamlessly switch between various attachments such as brush cutters or pole saws, enhancing the tool's versatility and making it suitable for multiple landscaping tasks.

Another noteworthy feature is the dual-line feed system that efficiently manages line advancement. This allows for quicker trimming sessions and less downtime for line replacement. The S31BC utilizes a bump feed mechanism, enabling users to quickly advance more line simply by tapping the trimmer head on the ground. This feature is especially valuable when tackling larger areas, as it allows for continuous operation without interrupting workflow.

Moreover, the Poulan S31BC is designed with durability in mind. Its rugged construction ensures that it withstands the rigors of regular use, offering reliable performance season after season. Additionally, the machine's lightweight design means that it is highly portable, making it easy to transport from one job site to another.

In conclusion, the Poulan S31BC is an excellent choice for anyone seeking an efficient and reliable trimmer. With its powerful 31cc engine, ergonomic design, interchangeable attachments, and user-friendly features, it caters to a range of trimming needs, making lawn care and maintenance much simpler. Whether you're a weekend warrior or a professional landscaper, the Poulan S31BC is engineered to deliver high performance, making it an invaluable addition to your outdoor toolkit.
Top Page Image Contents