Poulan S31BC instruction manual Attaching the Metal Shield, Installation of the Metal Blade

Page 6

ATTACHING THE METAL SHIELD

WARNING: The metal shield must be properly installed on the tool anytime the tool is used with a blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or by- standers. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the tube.

1.Place the metal shield under the gearbox, and align the screw holes.

Gearbox

3.Make sure the raised part of the retaining washer is facing the gearbox and the raised area fits into the hole in the center of the blade.

4.Slide the blade and retaining washer onto the shaft of the gearbox.

5.Place the cupped washer onto the shaft. Make sure the cupped side of the washer is toward the blade.

6.Install the blade nut by threading onto the shaft counterclockwise.

Gearbox

Shield

Shield

Dust Cup

Threaded Shaft

 

Retaining Washer

Blade

2.Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and secure- ly with the hex wrench provided.

INSTALLATION OF THE METAL BLADE

WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving.

WARNING: Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by Poulan/Weed Eater and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others.

NOTE: The dust cup and retaining washer are located on the gearbox shaft and not in the parts bag. All other fasteners mentioned in the follow- ing assembly steps are in the parts bag.

1.Remove the retaining washer from the threaded shaft of the gearbox. Leave the dust cup on the shaft.

2.Install the blade and the retaining washer over the threaded shaft.

Cupped Washer

Nut

NOTE: Make sure all parts are in place as il- lustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer.

7.Push in locking lever and hold.

8.Rotate blade nut until the locking lever falls into one of the grooves in the dust cup.

Locking Lever

9.Continue to hold in locking lever. This will keep the shaft from turning while tightening the blade nut.

10.Tighten blade nut firmly with a wrench.

11.Release locking lever.

12.Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must re- install.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Manual de Instrucciones Manuel d’Instructions Operator Safety Always WearCutting Safety UNIT/MAINTENANCE SafetyFuel Safety Transporting and StorageAssembly of Shoulder Strap Carton ContentsAdjust and Secure the HAN- Dlebar Tools RequiredAssembly Information Weed Blade Configuring Your UnitAssembly Information Trimmer Head Attaching the Plastic Shield and Trimmer HeadInstallation of the Metal Blade Attaching the Metal ShieldKnow Your Brushcutter ON/STOP SwitchHOW to Stop Your Unit Primer BulbHOW to Start Your Unit Starting a Warm EngineStarting a Flooded Engine Operating Position Trimmer Line Advance Operating Instructions for USE with Trimmer HeadCutting Methods Operating Instructions for USE with Weed Blade TrimmingCheck for Loose Fasteners and Parts Inspect and Clean Unit and DE- CalsClean AIR Filter Check for Damaged or Worn PartsReplacing the Line Blade ReplacementCarburetor Adjustment Seasonal StorageTroubleshooting Table Cause Remedy Electrolux Home PRODUCTS, INC

S31BC specifications

The Poulan S31BC is a versatile and powerful piece of outdoor equipment designed to meet the demands of both homeowners and landscaping professionals. This trimmer stands out for its efficiency, durability, and user-friendly features, making it a popular choice for tackling a variety of trimming tasks.

One of the standout features of the Poulan S31BC is its robust 31cc, 2-cycle engine. This powerful engine delivers the necessary torque to handle thick underbrush and tough weeds effortlessly. The 2-cycle engine is designed for high performance while remaining lightweight, which is crucial for extended use without causing fatigue to the operator. Additionally, the engine offers easy starting technology coupled with a smooth operation, allowing for hassle-free trimming in various environments.

The design of the Poulan S31BC also embraces ergonomic principles. Its lightweight frame and adjustable handle provide optimal control and comfort, reducing strain on the user's hands and back during extended use. This trimmer is equipped with a "split-shaft" construction that allows for easy attachment changes. Users can seamlessly switch between various attachments such as brush cutters or pole saws, enhancing the tool's versatility and making it suitable for multiple landscaping tasks.

Another noteworthy feature is the dual-line feed system that efficiently manages line advancement. This allows for quicker trimming sessions and less downtime for line replacement. The S31BC utilizes a bump feed mechanism, enabling users to quickly advance more line simply by tapping the trimmer head on the ground. This feature is especially valuable when tackling larger areas, as it allows for continuous operation without interrupting workflow.

Moreover, the Poulan S31BC is designed with durability in mind. Its rugged construction ensures that it withstands the rigors of regular use, offering reliable performance season after season. Additionally, the machine's lightweight design means that it is highly portable, making it easy to transport from one job site to another.

In conclusion, the Poulan S31BC is an excellent choice for anyone seeking an efficient and reliable trimmer. With its powerful 31cc engine, ergonomic design, interchangeable attachments, and user-friendly features, it caters to a range of trimming needs, making lawn care and maintenance much simpler. Whether you're a weekend warrior or a professional landscaper, the Poulan S31BC is engineered to deliver high performance, making it an invaluable addition to your outdoor toolkit.
Top Page Image Contents