Troy-Bilt TB60AF important safety instructions Know Your Unit, Assembly Instructions

Page 3
Knob
Fig. 3
Lower Shaft
Housing Fig. 4
Fig. 2
Fig. 1

KNOW YOUR UNIT

APPLICATIONS

As a trimmer:

•Cutting grass and light weeds

•Edging

•Decorative trimming around trees, fences, etc.

ASSEMBLY INSTRUCTIONS

WARNING: Make sure the motor is off and the battery is disconnected before assembling or disassembling any components.

This unit requires assembly.

UNPACKING

TOOLS REQUIRED:

• #2 Phillips screwdriver

• 3/8” Socket

Handle

Housing

Shaft Grip

•Carefully remove the product and any accessories from the box.

•Inspect the product carefully to make sure no breakage or damage occurred during shipping.

•Do not discard the packing material until you have carefully inspected and satisfactorily operated the product.

•If any parts are damaged or missing, please call 1-800-828-5500(U.S.) or 1-800-668-1238(Canada) for assistance.

Lock-off

Button

INSTALLING THE CUTTING HEAD SHIELD

D-Handle

Battery

Switch

Trigger

Battery Charger

EZ-Link™

Coupler

 

WARNING: To prevent serious personal

Mount

injury, never operate the unit without the

Bracket

 

cutting head shield in place.

 

Use the following instructions if the cutting head shield is

Cutting Head

Shield

not installed. Use only the instructions that apply to the

 

type of shaft and shield equipped with this unit.

 

1. Place the cutting head shield onto the mount bracket.

 

Align the holes in the cutting head shield with the holes

 

in the mount bracket. (Fig. 1)

 

2. Screw the 2 screws through the mount bracket and into

 

the cutting head shield until finger tight.

 

3. Using a #2 Phillips screwdriver, tighten the screws until

 

the cutting head shield is firmly in place. Tighten the

 

screws equally. The gap between the mount bracket and

 

the cutting head shield should be the same on each side.

 

Screws (2)

D-Handle

Cutting Head

Cutting Head Shield

Cutting Blades

INSTALLING THE CUTTING BLADES

Refer to Cutting Blade Replacement/Installation in the Maintenance and Repair Instructions section.

INSTALLING AND ADJUSTING THE D-HANDLE Installing the D-handle

1.Push the D-handle down onto the boom (Fig. 2), so that the bolt hole in the D-handle is to the right.

2.Insert the bolt into the hole in the handle. Do not tighten the bolt completely until after adjusting the D-handle.

Adjusting the D-handle

1.Make sure the bolt is loose enough for the D-handle to move along the boom.

2.While holding the unit in the operating position (Fig. 11), move the D-handle to the location that provides the best grip.

3.Tighten the bolt until the D-handle is secure. (Fig. 2)

OPERATING THE EZ-LINK SYSTEM

WARNING: To avoid serious personal injury and damage to the unit, shut the unit off before removing or installing add-ons.

NOTE: To make installing or removing the add-on easier, place the unit on the ground or on a work bench.

Installing the Add-On

NOTE: Remove the protective cap and gray spacer from the upper and lower shafts prior to assembling the add-on.

1.Turn the knob counterclockwise to loosen (Fig. 3).

2.While firmly holding the add-on, push it straight into the EZ-Link coupler (Fig. 4) until the release button snaps firmly into the primary hole (Fig. 5).

3.Turn the knob clockwise to tighten (Fig. 3).

Bolt

90˚ Edging Holes

(Trimmer Only)

Upper Shaft

Housing

 

CAUTION: Before operating this unit, be

Release Button

 

EZ-Link Coupler

 

sure that the release button is fully snapped

 

 

into the primary hole (Fig. 5), and that the knob

 

 

(Fig. 3) is securely tightened.

 

For decorative edging with the trimmer attachment, lock

 

the release button into one of the 90° holes (Fig. 3).

 

Check Flex Shaft Engagement Prior to Using

 

1.

Start the unit. Refer to Starting and Stopping Instructions.

Primary Hole

2.

Briefly engage and release the trigger.

 

3.

Check that add-on is operating.

Fig. 5

4.If the add-on is not operating, remove the add-on and repeat the steps for installing the add-on.

5.Recheck the operation of the add-on attachment.

NOTE: The blades are NOT installed on this product when first removed from packageing. Refer to Trimmer Blade Replacement/Installation.

Removing the Add-On

1.Turn the knob counterclockwise to loosen (Fig. 3).

2.Press and hold the release button (Fig. 5).

3.While firmly holding the upper shaft housing, pull the add-on out of the EZ-Link coupler (Fig. 4).

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Safety Alert Symbols Table of ContentsService Information Safety InformationDouble Insulated Safety and International SymbolsSymbol Meaning Safety Alert Symbol Wear Safety FootwearKnow Your Unit Assembly InstructionsStarting and Stopping Instructions Assembly Instructions Operating InstructionsSpecifications Maintenance and Repair InstructionsCleaning and Storage TroubleshootingPage Page Page Información Sobre Servicio Información DE SeguridadSímbolos DE Alerta DE Seguridad Tabla DE ContenidoUSE Protección Para LOS Ojos Y Oídos Símbolos Internacionales Y DE SeguridadSímbolo Significado Símbolo DE Alerta DE Seguridad LEA EL Manual DEL OperadorInstrucciones DE Ensamblaje Conozca SU UnidadInstrucciones DE Arranque Y Parada Instrucciones DE Ensamblaje Instrucciones DE OperaciónEspecificaciones Localización Y Solución DE ProblemasPage Page TROY-BILT LLC

TB60AF specifications

The Troy-Bilt TB60AF is a versatile and efficient addition to any outdoor maintenance toolkit. Designed for homeowners who value power and ease of use, this gas-powered string trimmer is engineered to tackle a variety of yard tasks, from trimming grass to tackling overgrown weeds and brush.

One of the standout features of the TB60AF is its dependable 60cc 2-cycle engine, which provides ample power for various tasks. This powerful engine enables users to complete yard work quickly and efficiently, even in more challenging conditions. Its lightweight design, coupled with a balanced structure, ensures that users can maneuver it comfortably during extended use without excessive fatigue.

The TB60AF utilizes a 17-inch cutting swath, allowing for a wider trimming area and reducing the time spent on yard work. This increased cutting width is ideal for managing larger sections of grass and weeds with less effort than traditional, narrower trimmers. Additionally, the trimmer features the JumpStart technology, which provides an easy starting experience. This system significantly reduces the hassle of starting the engine, making it more accessible for users who may struggle with traditional starting methods.

Another important aspect of the TB60AF is its innovative Smart Start technology. This feature is designed to reduce the amount of pull force needed to start the engine, ensuring a smooth start every time. Coupled with easy-to-replace trimmer line, maintenance and operation are straightforward, making it an attractive choice for novices and seasoned users alike.

The adjustable handle design of the TB60AF enhances comfort and control during operation. Users can personalize the handle's position for better ergonomics, which can be especially beneficial when navigating around obstacles or working in tight spaces.

In terms of durability, the TB60AF is built with high-quality materials designed to withstand the rigors of outdoor use. The robust construction helps ensure longevity, allowing homeowners to depend on it season after season.

In summary, the Troy-Bilt TB60AF is an exceptional choice for those seeking a reliable and efficient string trimmer. With its powerful 60cc engine, wide cutting swath, user-friendly technologies, and ergonomic design, it stands out as a top contender for anyone looking to maintain a beautiful yard with ease and precision.
Top Page Image Contents