Maintenance and Repair Instructions

	WARNING: Before inspecting, cleaning, or
	servicing the unit, stop the motor, wait for all
	moving parts to stop and remove the battery.
	Failure to follow these instructions can result in	Cutting
	serious personal injury or property damage.	Cutting
	serious personal injury or property damage.	Head
	CUTTING BLADE REPLACEMENT/INSTALLATION
	WARNING: Never use metal-reinforced line,	Cap Tab
	WARNING: Never use metal-reinforced line,
	wire, chain or rope. These can break off and
	become dangerous projectiles.
		Fig. 13

CLEANING AND STORAGE

WARNING: Do not let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. These chemicals may damage, weaken and destroy plastic, which may result in serious personal injury.

WARNING: To avoid risk of fire, electric shock or electrocution: DO NOT use a damp cloth or detergent on the battery or battery charger. Wipe the outside with a dry, soft cloth.

CLEANING INSTRUCTIONS

1.	Stop the motor and wait for all moving parts to stop.
2.	Remove the battery from the unit.
3.	Wipe the unit down with a damp cloth. Do not douse the unit with water. Do not use solvents or

Always use original equipment manufacturer replacement blades. Blades other than those specified may make the motor overheat or fail. This unit uses four (4) green cutting blades.

Removing the Cutting Blades

1.Remove the cutting head cap by pressing in on both cap tabs and then pulling down on the cap. (Fig. 13)

2.Turn the cutting head over and grab an individual blade near the cutting head and wiggle it up and down until blade comes loose. (Fig. 14)

3.Repeat step 2 until all blades are removed.

Installing the Cutting Blades

WARNING: Always install an even number of blades (2 or 4). NEVER install an uneven number of blades (1 or 3) as this will make the unit unstable and hard to control, which could result in serious personal injury.

4.Take the new blade so that the loop at the end is facing away and to the right. (Fig. 14)

5.Place the loop onto the peg and adjust it so that it fits into the slot on the cutting head. (Fig. 14)

6.Press down on the loop end of the blade till it is securely in place.

7.Repeat steps 4 thru 6 until all 4 blades are in place. (Fig. 14)

Peg

Cutting

Blade

Blade Slot

Fig. 14

Cap

Cap Tab

Cutting Head

Tab Slots

Fig. 15

	strong detergents.
4.	Scrape the guard and spool area to remove dried clippings and mud.
5.	Brush or blow dust, debris and grass clippings out of the air vents. Keep them free or obstructions
STORAGE INSTRUCTIONS
1.	Follow the Cleaning Instructions listed above.

2.Store the unit indoors in a dry, high and/or locked location, out of the reach of children and other unauthorized persons.

TROUBLESHOOTING

CAUSE	SOLUTION

THE MOTOR OPERATES SLOWLY OR WILL NOT OPERATE

The battery lacks sufficient charge	Charge the battery

THE BATTERY WILL NOT CHARGE

There is no power to the charger or battery	Check the charger and charging station
The battery has failed	Replace the battery

8.Replace the cutting head cap, making sure to align the cap tabs with the cutting head tab slots. (Fig. 15)

CHARGER MAINTENANCE

•Keep the charger clean and clear of debris. Do not allow foreign material into the recessed cavity or on the contacts.

•Wipe with a dry cloth. Do not use solvents, water or place in wet conditions.

•Always unplug the charger when not in use.

•The battery pack may be stored in the charger. However, it is recommended to disconnect the charger from the power source.

•To ensure safety and reliability, all repairs should be performed by a qualified service technician.

•Check that the charger contacts have not been shorted by debris or foreign material.

•Keep the charger and battery pack in an area that is between 65 and 75˚ F (18 and 24˚ C).

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

The following toxic and corrosive materials are used in this units battery pack:

LITHIUM-ION, a toxic material.

WARNING: All toxic materials must be disposed of in a specified manner to prevent contamination of the environment. Before disposing of damaged or worn out lithium-ion battery packs, contact your local waste disposal agency for information and specific instructions. Take batteries to a local recycling and or disposal center, certified for lithium- ion battery disposal.

WARNING: Do not use the battery pack if there are cracks or if it breaks, regardless if there is leakage or not. Replace with a new battery pack. DO NOT ATTEMPT TO REPAIR! As this may cause severe personal injury due to explosion or electrical shock.

To avoid damage to the environment:

•DO NOT attempt to remove or destroy any of the battery pack components.

•DO NOT open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

•DO NOT place the battery pack in the regular household trash.

•DO NOT dispose of the battery in a fire. The cell may explode.

•DO NOT place them where they will become part of any waste landfill or municipal solid waste stream.

•Cover the battery terminals with heavy-duty adhesive tape.

•If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in your eyes or on your skin, and do not swallow it.

•Dispose of the battery pack in accordance with local, state and federal regulations.

NOTE: For maintenance beyond the minor adjustments listed above, or for replacement parts, please call the Customer Support Department at 1-800-828-5500(U.S.) or 1-800-668-1238(Canada).

SPECIFICATIONS*

Motor Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cordless, Battery-powered Motor Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V Motor Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5000 rpm Unit Weight (with the cutting head shield and D-handle, but without the battery) . . . 8.45 lbs. (3.83 kg) Cutting Path Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 in. (35.6 cm) Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V Lithium Charge Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Hours Battery Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 Lbs. (0.81 kg) Optimum Charging Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32° to 86° F (0° to 30° C) Battery Charger Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 V 60 Hz AC only Battery Charger Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Lbs. (0.54 kg)

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

ACCESSORIES
Model #	Part #	Description
TB20V50	49MLI50Y966	20V	Lithium-ion Battery
TBCHGR	49MALBCL966	20V	Lithium-ion Battery Charger
. . . . . . . . . . . . . . . .	49UAFGRK703	Cutting Blades
. . . . . . . . . . . . . . . .	49M7533K953	Shoulder Strap

TB60AF specifications

The Troy-Bilt TB60AF is a versatile and efficient addition to any outdoor maintenance toolkit. Designed for homeowners who value power and ease of use, this gas-powered string trimmer is engineered to tackle a variety of yard tasks, from trimming grass to tackling overgrown weeds and brush.

One of the standout features of the TB60AF is its dependable 60cc 2-cycle engine, which provides ample power for various tasks. This powerful engine enables users to complete yard work quickly and efficiently, even in more challenging conditions. Its lightweight design, coupled with a balanced structure, ensures that users can maneuver it comfortably during extended use without excessive fatigue.

The TB60AF utilizes a 17-inch cutting swath, allowing for a wider trimming area and reducing the time spent on yard work. This increased cutting width is ideal for managing larger sections of grass and weeds with less effort than traditional, narrower trimmers. Additionally, the trimmer features the JumpStart technology, which provides an easy starting experience. This system significantly reduces the hassle of starting the engine, making it more accessible for users who may struggle with traditional starting methods.

Another important aspect of the TB60AF is its innovative Smart Start technology. This feature is designed to reduce the amount of pull force needed to start the engine, ensuring a smooth start every time. Coupled with easy-to-replace trimmer line, maintenance and operation are straightforward, making it an attractive choice for novices and seasoned users alike.

The adjustable handle design of the TB60AF enhances comfort and control during operation. Users can personalize the handle's position for better ergonomics, which can be especially beneficial when navigating around obstacles or working in tight spaces.

In terms of durability, the TB60AF is built with high-quality materials designed to withstand the rigors of outdoor use. The robust construction helps ensure longevity, allowing homeowners to depend on it season after season.

In summary, the Troy-Bilt TB60AF is an exceptional choice for those seeking a reliable and efficient string trimmer. With its powerful 60cc engine, wide cutting swath, user-friendly technologies, and ergonomic design, it stands out as a top contender for anyone looking to maintain a beautiful yard with ease and precision.