WARNING: If received assembled, re- peat all steps to ensure your unit is properly as- sembled and all fasteners are secure.
Examine parts for damage. Do not use dam- aged parts.
NOTE: If you need assistance or find that parts are missing or damaged, call
TOOLS REQUIRED
SHex wrench (provided)
HANDLEBAR ASSEMBLY
DANGER: RISK OF CUT. To avoid se- rious injury, the barrier portion of the handle- bar must be installed as shown on the upper tube of the powerhead to provide a barrier be- tween operator and the spinning blade. Attach tube clamp above arrow on safety warning de- cal on the upper tube (powerhead end of unit). Ensure handlebar is positioned on handlebar clamp between the arrows on the handlebar decal.
NOTE: The tube clamp base has four spacer tabs attached. These tabs are provided to adapt this attachment for use with power- heads that have a 1∀ diameter upper tube (the tube clamp will not tighten down securely on the 1∀ diameter upper tube without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the clamp base. These tabs are not needed for powerheads with a 7/8∀ up- per tube.
HANDLEBAR CLAMP BASE
Spacer Tabs
Spacer Tabs 
positioned for use on 1∀ diameter upper tube
1.Place the tube clamp over the upper tube above the arrow on the safety decal.
2.Position the clamp base under the upper tube and align the tube clamp and clamp base screw holes (use spacer tabs be- tween tube clamp and clamp base if nec- essary to secure clamp, i.e. for 1∀ diame- ter upper tube).
Handlebar
POWERHEAD
END
Handlebar Clamp between arrows on handlebar decal
Clamp |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Clamp | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Base | |||
Knob |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
Tube |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Screws | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
Clamp |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
| Arrow on | |||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
| Safety Decal | |||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ATTACHMENT
END
3.Insert four screws into the screw holes.
4.Secure tube clamp by tightening screws with the hex wrench.
5.Position the handlebar as shown, ensur- ing the handlebar is positioned on the handlebar clamp between the two arrows on the handlebar decal.
6.Retighten handlebar by turning clamp knob clockwise until handlebar is secure and stationary in clamp (clamp knob can- not be overtightened).
SHOULDER STRAP ASSEMBLY
WARNING: Proper shoulder strap and handlebar adjustments are required before use. The shoulder strap clamp must be installed as shown above the handlebar on the upper tube (powerhead end of unit).
NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are pro- vided to adapt this attachment for use with powerheads that have a 1∀ diameter upper tube (the shoulder strap clamp will not tighten down securely on the 1∀ diameter upper tube without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for powerheads with a 7/8∀ upper tube.
4