Poulan 545146926 HOW to Start Your Unit, Starting a Cold Engine, Starting a Flooded Engine

Page 9

ON/OFF Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move the start lever to the START posi- tion.

Starter Handle

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL:

Edger . . . . . . . . . . . . . . . . . . . . . . PPB1000E Cultivator . . . . . . . . . . . . . . . . . . . PPB2000T Blower . . . . . . . . . . . . . . . . . . . . . PPB3000B Brushcutter . . . . . . . . . . . . . . . . . PPB4000C Pruner . . . . . . . . . . . . . . . . . . . . . PPB5000P

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL AT- TACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

Upper Shaft

Coupler

Lower

LOOSEN

Start

Lever

Primer Bulb

Muffler

5.Pull starter rope handle sharply until en- gine starts and runs.

6.Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly.

3.Pull starter rope sharply while squeezing throttle trigger until engine runs.

NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned OFF. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

Attachment

TIGHTEN Knob

2.Press and hold the locking/release button. Locking/Release

Button

Coupler

Upper Shaft

Lower Attachment

 

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

2.Position locking/release button of attach- ment into guide recess of coupler.

3.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

4.Before using the unit, tighten the knob se- curely by turning clockwise.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents PPB150E Safety Rules Operator SafetyUL Classified Product Notice Fuel Safety Unit / Maintenance SafetyLine Trimmer Safety Transporting and StorageBLOWER/VACUUM Safety Edger SafetyBrushcutter Safety Always use the handlebar when using edg- er attachmentHedge Trimmer Safety Cultivator SafetyPole Pruner Safety Proboscis noseSnow Thrower Safety Installing Trimmer ATTACH- Ment AssemblyAdjusting the Assist Handle Attaching ShieldOperation Installing Optional ATTACH- Ments HOW to Start Your UnitStarting a Cold Engine Starting a Flooded EngineTrimmer Line Advance Operating PositionCutting Methods Secondary Hole Locking/Release Button in Primary HoleInspect and Clean Unit and Labels MaintenanceClean AIR Filter Check for Loose Fasteners and PartsCarburetor Adjustment Service and AdjustmentsMuffler and Spark ARREST- ING Screen Replace Spark PlugFuel System Seasonal StorageEngine OtherTroubleshooting Table Cause Remedy Ligations The U.S. Environmental Limited WarrantyIntermediate 125 hours Extended 300 hours

545146926 specifications

The Poulan 545146926 is a powerful and versatile chainsaw designed for both professional and home use. Known for its robust performance and user-friendly features, this model offers an array of specifications that cater to various cutting tasks, from trimming branches to felling trees.

One of the standout features of the Poulan 545146926 is its efficient engine. The chainsaw is powered by a reliable 50cc two-cycle engine, which delivers ample power while maintaining fuel efficiency. This balance makes it suitable for extended use without the constant need for refueling. Additionally, the engine's design minimizes emissions, allowing for a more environmentally friendly operation, in keeping with modern standards.

The chainsaw is equipped with a 20-inch bar and chain, offering an optimal cutting length for a wide range of applications. This extended reach allows the user to tackle larger trees and thick branches with ease, making the Poulan 545146926 an excellent choice for both professional loggers and homeowners with extensive landscaping needs.

Safety is a priority in the design of the Poulan 545146926. The chainsaw features several safety mechanisms, including a chain brake that activates in the event of a kickback, reducing the risk of injury during operation. Furthermore, the comfortable handle design aids in reducing vibrations, which makes for a smoother cutting experience, minimizing fatigue during longer projects.

Another notable technology featured in this chainsaw is its easy-start system. This mechanism reduces the effort required to start the engine, allowing users to get to work quickly without struggling with traditional pull-start engines. The improved air filtration system further enhances performance, ensuring the engine operates smoothly and efficiently by keeping dirt and debris at bay.

In terms of maintenance, the Poulan 545146926 is designed for ease of use. Its tool-less chain tensioning system simplifies adjustments, allowing users to maintain optimal chain tension effortlessly. Additionally, the easy-access air filter and fuel cap streamline routine checks, making it convenient for users to keep their chainsaw in top working condition.

In summary, the Poulan 545146926 combines power, safety, and user-friendly features, making it an ideal choice for anyone needing a reliable chainsaw for various cutting tasks. Its advanced technology, efficient design, and focus on safety provide a comprehensive solution for both amateur and seasoned users.
Top Page Image Contents