Poulan FX25 LE, XT250 LE Trimmer Line Advance, Cutting Methods, Tip of the Line Does The Cutting

Page 6

To stop engine:

SRelease the throttle trigger.

S Push and release the engine ON/STOP switch.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2 in. (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle.

The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being oper- ated.

To advance line:

SOperate the engine at full throttle.

SHold the trimmer head parallel to and above

the grassy area.

STap the bottom of the trimmer head lightly on the ground one time. Approximately 2 in. (5 cm) of line will be advanced with each tap.

Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head.

If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to ob- tain the most efficient line length.

WARNING: Use only 0.080” (2 mm) diameter line. Other sizes and shapes of line will not advance properly and will result in im- proper cutting head function or can cause se- rious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous mis- sile that can cause serious injury.

SFor trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

S During light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence wire.

SFor mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

3 in. (8 cm) Above Ground

SCALPING -- The scalping technique re- moves unwanted vegetationdown to the ground. Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

Scalping

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

SThe tip of the line does the cutting. You will achieve the best performance and mini- mum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

Mowing

Tip of the Line Does The Cutting

Right

Line Crowded Into Work Area

Wrong

SWEEPING -- The fanning action of the rotat- ing line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side.

S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. To help avoid damage especially to delicate vegetation or trees with tender bark, shorten line to 4--5 in. (10--13 cm) and use at less than full throttle.

Sweeping

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Manual de Instrucciones Manuel d’Instructions Operator Safety Unit / Maintenance SafetyFuel Safety Transporting and Storage Cutting SafetyAdjusting the Handle Attaching ShieldKnow Your Trimmer ON/STOP Switch ChokeHOW to Stop Your Unit Primer BulbStarting a Flooded Engine HOW to Start Your UnitStarting a Warm Engine Operating PositionTip of the Line Does The Cutting Trimmer Line AdvanceCutting Methods Line Crowded Into Work AreaCheck for Loose Fasteners and Parts Inspect and Clean Unit and LabelsClean AIR Filter Check for Damaged or Worn PartsSeasonal Storage Line ReplacementCarburetor Adjustment Fuel SystemTroubleshooting Table Cause Remedy OtherYour Warranty Rights and Obliga Control Warranty Parts List Car

FX25 LE, XT250 LE specifications

The Poulan FX25 LE and XT250 LE are two powerful trimmers designed to meet the demands of landscaping professionals and homeowners alike. Packed with innovation, these models stand out in terms of performance, user comfort, and usability.

At the heart of the Poulan FX25 LE is a robust 25cc 2-stroke engine. This engine provides ample power for tackling thick grass, stubborn weeds, and overgrown areas with ease. The XT250 LE features a slightly larger 26cc engine, enhancing its capabilities for heavier-duty tasks. The engines are designed for efficiency, delivering excellent fuel economy while maintaining a high-power output, essential for prolonged use.

Both models incorporate advanced starting technology. The Easy Start feature ensures that users can get their trimmers running effortlessly, reducing the frustration commonly associated with starting small engines. These trimmers are equipped with an automatic choke, enhancing their user-friendliness, especially for those who may not be familiar with two-stroke engines.

Another highlight of these models is their lightweight design, which significantly reduces user fatigue during extended periods of operation. Weighing in at less than 10 pounds, they are easy to maneuver, making them ideal for trimming delicate landscapes and navigating tight corners.

The Poulan FX25 LE and XT250 LE come with ergonomically designed handles that provide a comfortable grip, allowing for prolonged usage without compromising control. The adjustable harness on the XT250 LE not only adds comfort but also distributes weight more evenly, adding to the ease of operation.

Additionally, both trimmers feature a dual-line cutting system, which provides a wider cutting path to enhance efficiency. The rapid reload spool allows users to replace the line quickly and easily without the need for additional tools. This feature saves time and ensures that users spend more time trimming and less time on maintenance.

Durability is another significant aspect of these models. Constructed with high-quality materials, the Poulan FX25 LE and XT250 LE are built to withstand the rigors of outdoor use. They are also equipped with protective shields to safeguard the user from debris while operating.

In summary, the Poulan FX25 LE and XT250 LE trimmers offer a powerful, efficient, and user-friendly experience. With features such as robust engines, easy starting mechanics, lightweight design, ergonomic handles, and a dual-line cutting system, they are well-suited for any landscaping task. Whether you are a homeowner maintaining your garden or a professional landscaper, these trimmers provide the reliability and performance necessary to achieve excellent results.
Top Page Image Contents