Poulan FX25 LE, XT250 LE Line Replacement, Carburetor Adjustment, Seasonal Storage, Fuel System

Page 8

LINE REPLACEMENT

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with pre--wound spool, or cut a length of 20 feet of 0.080! (2 mm) diameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert one end of the line about 1/2 inch (1 cm) into the small hole on the inside of spool.

Small

Hole Spool

Line in Notch

Hub

Line exit hole

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrow found on the spool.

6.Push the line into the notche, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the line into the the exit holebin the hub as shown in the illustration.

8.Align the notch with the line exit hole.

9.Push spool into hub until it snaps into place.

10.Pull the line extending outside of the hub to release it from the notch.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold

the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed

Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric

motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom-

mended type and heat range. S Clean air filter.

8

Image 8
Contents Manual de Instrucciones Manuel d’Instructions Fuel Safety Operator SafetyUnit / Maintenance Safety Cutting Safety Adjusting the HandleTransporting and Storage Attaching ShieldON/STOP Switch Choke HOW to Stop Your UnitKnow Your Trimmer Primer BulbHOW to Start Your Unit Starting a Warm EngineStarting a Flooded Engine Operating PositionTrimmer Line Advance Cutting MethodsTip of the Line Does The Cutting Line Crowded Into Work AreaInspect and Clean Unit and Labels Clean AIR FilterCheck for Loose Fasteners and Parts Check for Damaged or Worn PartsLine Replacement Carburetor AdjustmentSeasonal Storage Fuel SystemTroubleshooting Table Cause Remedy OtherYour Warranty Rights and Obliga Control Warranty Parts List Car

FX25 LE, XT250 LE specifications

The Poulan FX25 LE and XT250 LE are two powerful trimmers designed to meet the demands of landscaping professionals and homeowners alike. Packed with innovation, these models stand out in terms of performance, user comfort, and usability.

At the heart of the Poulan FX25 LE is a robust 25cc 2-stroke engine. This engine provides ample power for tackling thick grass, stubborn weeds, and overgrown areas with ease. The XT250 LE features a slightly larger 26cc engine, enhancing its capabilities for heavier-duty tasks. The engines are designed for efficiency, delivering excellent fuel economy while maintaining a high-power output, essential for prolonged use.

Both models incorporate advanced starting technology. The Easy Start feature ensures that users can get their trimmers running effortlessly, reducing the frustration commonly associated with starting small engines. These trimmers are equipped with an automatic choke, enhancing their user-friendliness, especially for those who may not be familiar with two-stroke engines.

Another highlight of these models is their lightweight design, which significantly reduces user fatigue during extended periods of operation. Weighing in at less than 10 pounds, they are easy to maneuver, making them ideal for trimming delicate landscapes and navigating tight corners.

The Poulan FX25 LE and XT250 LE come with ergonomically designed handles that provide a comfortable grip, allowing for prolonged usage without compromising control. The adjustable harness on the XT250 LE not only adds comfort but also distributes weight more evenly, adding to the ease of operation.

Additionally, both trimmers feature a dual-line cutting system, which provides a wider cutting path to enhance efficiency. The rapid reload spool allows users to replace the line quickly and easily without the need for additional tools. This feature saves time and ensures that users spend more time trimming and less time on maintenance.

Durability is another significant aspect of these models. Constructed with high-quality materials, the Poulan FX25 LE and XT250 LE are built to withstand the rigors of outdoor use. They are also equipped with protective shields to safeguard the user from debris while operating.

In summary, the Poulan FX25 LE and XT250 LE trimmers offer a powerful, efficient, and user-friendly experience. With features such as robust engines, easy starting mechanics, lightweight design, ergonomic handles, and a dual-line cutting system, they are well-suited for any landscaping task. Whether you are a homeowner maintaining your garden or a professional landscaper, these trimmers provide the reliability and performance necessary to achieve excellent results.