Poulan PP025 instruction manual Service and Adjustments

Page 12

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot S Air Filter

S Housing Screws

S Assist Handle Screw S Debris Shield

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SON/OFF Switch -- Ensure ON/OFF switch

functions properly by moving the switch to the OFF position. Make sure engine stops; then restart engine and continue.

SFuel Tank -- Discontinue use of unit if fuel tank shows signs of damage or leaks.

SDebris Shield -- Discontinue use of unit if debris shield is damaged.

INSPECT AND CLEAN UNIT AND LABELS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and labels using a damp cloth with a mild deter- gent.

SWipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine perform- ance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation.

1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed.

2. Remove parts by pressing button to re- lease air filter cover.

NOTE: To avoid creating a fire hazard or producing harmful evaporative emissions, do not clean filter in gasoline or other flammable solvent.

3.Wash the filter in soap and water.

4.Allow filter to dry.

5.Replace parts.

Button

Air Filter

Air Filter Cover

MUFFLER AND SPARK ARREST- ING SCREEN

WARNING: The muffler on this prod- uct contains chemicals known to the State of California to cause cancer.

As your unit is used, carbon deposits build up on the muffler and spark arresting screen. For normal homeowner use, however, the muffler and spark arresting screen will not re- quire any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Igni- tion timing is fixed and nonadjustable.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and discard.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench.

4.Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

1.Press the tabs on the side of the trimmer head and remove cover and spool.

Cover

Tab

Tap Button

2.Remove any remaining line.

3.Clean dirt and debris from all parts. Re- place spool if it is worn or damaged.

4.Replace with a pre-wound spool, or re- place line using a 25 feet (8 meters) length of 0.080 inch (2 mm) diameter Poulan PRO brand line.

5.When installing new line on an existing spool, hold the spool as shown in the il- lustration below.

6.Bend the line at the midpoint and insert the bend into the slot in the center rim of the spool. Ensure line snaps into position in the slot.

Slot

Spool

7.With your finger between the lines, wrap the lines evenly and firmly around the spool in a clockwise direction.

8.Position the lines in the guide slots.

12

Image 12
Contents PP025 Safety Rules Operator SafetyUnit / Maintenance Safety Fuel Safety Line Trimmer SafetyEdger Safety Transporting and StorageBLOWER/VACUUM Safety Brushcutter SafetyCultivator Safety Hedge Trimmer Safety Pole Pruner SafetyFor damage Cover in place and properly securedAssembly Snow Thrower SafetyInstalling Trimmer ATTACH- Ment Adjusting the Assist Handle Attaching ShieldPrimary Hole Secondary HoleOperation HOW to Stop Your Unit HOW to Start Your UnitStarting a Cold Engine Starting a Warm EngineInstalling Optional ATTACH- Ments Operating PositionTrimmer Line Advance Maintenance Cutting MethodsInches 8 cm above ground Service and Adjustments Carburetor Adjustment Seasonal StorageFuel System PortingTroubleshooting Table EngineOther Trouble Cause RemedyLimited Warranty Ligations The U.S. EnvironmentalService 800--554--6723