Homelite UT20811E manual String Replacement, Cleaning the Exhaust Port and Muffler Spark Arrestor

Page 12

MAINTENANCE

STRING REPLACEMENT

See Figures 12, 13, 14, and 15.

1.Stop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer. Turn counterclockwise.

2.Remove the spool from the string head. NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool.

3.Cut two pieces of string, each being approximately 9 ft. (2.7 m) long. Use only .080 in. (2.0 mm) diameter monofilament string.

4.Insert the first string into the anchor hole in the upper part of the spool. Wind the first string around the upper part of the spool counterclockwise, as shown by the arrows on the spool. Place string in the slot on upper spool flange, leaving about 6 in. (152 mm) extended beyond the slot. Do not overfill. After winding the string, there should be at least 1/4 in. (6 mm) between the wound string and the outside edge of the spool.

5.Repeat above step with second string, using the bottom part of spool. Do not overfill.

6.Replace the spool and the spool retainer. Refer to "Spool Replacement " earlier in this manual.

SPRING

SPOOL

ARROWS ON

SPOOL

ANCHOR

HOLE

FIRST STRING

Fig. 12

FIRST STRING

SLOT

CLEANING THE EXHAUST PORT AND MUFFLER

NOTE: Depending on the type of fuel used, the type and amount of oil used, and/or your operating condi- tions, the exhaust port and muffler may become blocked with carbon deposits. If you notice a power loss with your gas powered tool, you may need to remove these deposits to restore performance. We highly recommended that only qualified service techni- cians perform this service.

SPARK ARRESTOR

The spark arrestor must be cleaned or replaced every 25 hours or yearly to ensure proper performance of your product. Spark arrestors may be in different locations depending on the model purchased. Please contact your nearest service dealer for the location of the spark arrestor for your model.

Cleaning Instructions:

■Remove the spark arrestor from the muffler.

■If your spark arrestor is made of a fiberglass mate- rial, discard and replace.

■If your spark arrestor is made of a metal material follow these cleaning instructions:

1.Spray the spark arrestor with a quality carbon cleaner.

2.Gently clean using a wire brush.

3.Install the new or cleaned spark arrestor and reassemble completely before use.

Fig. 13

SECOND

STRING

Fig. 14

SLOT

ARROWS ON

 

SPOOL

Fig. 15

Page 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operators Manual Table of Contents Important Safety InstructionsIntroduction Specific Safety Rules for Trimmer USE Symbols Symbol Name ExplanationSpecifications FeaturesUnpacking InstructionsAssembly Attaching the Power Head to the Trimmer AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerHandle Grass DeflectorFueling and Refueling the Trimmer Operating the TrimmerFuel Mixture Fuel Mixture Premium Exact MIX Gasoline OILOperation Advancing the StringCUT OFF Blade Cutting TipsStarting and Stopping SeeTo Start a Cold Engine To Start a Warm EngineMaintenance Spool Replacement EZ Line TAP Advance SystemNEW Prewound Spool See Figures 10String Replacement Cleaning the Exhaust Port and Muffler Spark ArrestorSee Figures 12, 13, 14, Arrows on Spool Anchor Hole First StringReplacing and Cleaning AIR Filter Fuel CAPSpark Plug Storing the Trimmer 1 Month or LongerTroubleshooting Speed. See FigureIdle Speed Screw Mixture Needle Warranty Limited Warranty StatementManufacturers Warranty Coverage AIR Filter Assy Service Parts DescriptionService Repair Parts California Proposition

UT20811E specifications

The Homelite UT20811E is a powerful electric string trimmer designed to meet the demands of homeowners and professional landscapers alike. This model stands out for its efficiency and user-friendly features, making it an ideal choice for tackling overgrown lawns, edging flower beds, and maintaining tidy borders around driveways and sidewalks.

One of the main features of the UT20811E is its robust 13-amp motor, which delivers impressive power for cutting through thick weeds and grass. This electric trimmer eliminates the need for gasoline and oil, reducing the environmental impact while providing a quieter lawn care experience. With a no-pull, easy-start operation, users can simply plug in the trimmer and get to work with minimal fuss.

The UT20811E incorporates a dual-line automatic feed system, ensuring a continuous supply of trimmer line as you work. This feature saves time and effort, eliminating the need for manual line adjustments. The trimmer is equipped with a 0.065-inch line diameter, allowing for efficient cutting and improved performance.

In addition to its cutting capabilities, the Homelite UT20811E offers a telescoping shaft that adjusts to accommodate users of different heights, promoting ergonomic comfort during extended use. The rotating head provides versatility as the trimmer can smoothly transition from trimming to edging, giving users the ability to achieve a professional-looking finish.

Safety is also a priority with this model; it features a protective guard that shields users from debris and allows for close trimming around delicate plants. The lightweight design of the trimmer makes it easy to maneuver, reducing fatigue during longer jobs.

The Homelite UT20811E is further enhanced by its durable construction, ensuring longevity and reliability. The product also comes with a 3-year warranty, providing users with peace of mind regarding its performance and durability over time.

In summary, the Homelite UT20811E electric string trimmer combines power, convenience, and safety features to offer an exceptional tool for lawn care. Whether you are a weekend warrior or a seasoned professional, this versatile trimmer is designed to exceed expectations, making yard maintenance more efficient and enjoyable.
Top Page Image Contents