Husqvarna 333R-Series manual Fine adjustment of the idle speed T, High speed jet H

Page 25

MAINTENANCE

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

T

WARNING! If the idle speed cannot be

!adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

H

Note that the engine should be loaded when you adjust the high speed jet H. You should therefore fit the trimmer head T35 (2.7 mm cord) before adjusting the high speed jet. The cord length should be standard, i.e. to the knife on the trimmer guard.

Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly.

H

CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a revolution counter at their disposal.

Correctly adjusted carburettor

When the carburettor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed. It is also important that the cutting attachment does not rotate at idle. If the low speed jet L is set too lean it may cause starting difficulties and poor acceleration.

If the high speed jet H is set too lean it will result in less power, less performance, poor acceleration and/or damage to the engine.

If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed.

Adjusting the start throttle speed

The correct start throttle speed is set by means of an adjuster on the rear of the handle next to the cable. Use this screw (4

mmAllen screw) to increase or decrease the start throttle speed.

Proceed as follows:

1Run the machine at idle.

2Press the start throttle lock as described under the heading Starting and stopping.

3If the start throttle speed is too low (below 4000 rpm), turn the adjuster screw A clockwise until the cutting attachment starts to rotate. Then turn A clockwise a further 1/2 turn.

4If the start throttle speed is too high, turn the adjuster screw A anticlockwise until the cutting attachment stops. Then turn adjuster screw A clockwise a further 1/2 turn.

WARNING! If the idle speed cannot be

!adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 333R 335RX-series Symbols KEY to SymbolsContents Dear Customer IntroductionWhat is what on the clearing saw? What is WHAT?Personal protective equipment General Safety PrecautionsStop switch Machine′s safety equipmentThrottle lock Vibration damping system Cutting attachment guardQuick release MufflerLocking nut Cutting equipment Cutting equipmentSharpening grass cutters and grass blades Trimmer head Sharpening the saw bladeAssembling the handlebar and throttle AssemblyAssembling the cutting equipment Fitting the guard extensionFitting the blade guard and saw blade Fitting a blade guard, grass blade and grass cutterFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness Spreading the load on your shouldersTriobalance harness Adjusting the harnessCorrect balance Fuel Handling Fuel safetyFuel Mixing FuellingCheck before starting Starting and StoppingStarting and stopping StartingStopping For throttle handles with a start throttle lockWorking Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeGrass trimming with a trimmer head Clearing Carburettor MaintenanceCorrectly adjusted carburettor Fine adjustment of the idle speed TAdjusting the start throttle speed High speed jet HCooling system MufflerBevel gear Air filter Cleaning the air filterSpark plug Oiling the air filterMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataApplies to Europe only EC-declaration of conformityPage S35 095-.106 T35 T45 Auto Trimmy SII ´z+R56¶6u¨ Page 1150212-26 ´z+R56¶6u¨ ´z+R56¶6u¨

333R-Series specifications

The Husqvarna 333R-Series represents a pinnacle of engineering in the realm of professional-grade brushcutters. Designed for heavy-duty performance, the 333R is an ideal choice for landscape professionals and homeowners alike, providing an efficient solution for tackling thick grass, weeds, and brush. Its robust construction and advanced features make it a reliable tool in various trimming and clearing applications.

One of the standout characteristics of the 333R-Series is its powerful engine. Equipped with a high-performance 32.6 cc, 2-stroke engine, it delivers exceptional torque and speed, enabling users to cut through dense undergrowth with ease. The engine is designed with Husqvarna's X-Torq technology, which optimizes fuel efficiency by reducing fuel consumption and emissions. This not only benefits the environment but also allows for longer operating times between refuels, a crucial factor for professional landscapers working long hours.

The ergonomics of the 333R-Series enhance user experience significantly. Its lightweight design, combined with a balanced frame, reduces fatigue during prolonged use. The comfortable shoulder harness ensures that the weight of the tool is evenly distributed, allowing for easier maneuverability without sacrificing power. Additionally, the adjustable handlebar provides customizable grip positions, ensuring comfort for users of all sizes.

The cutting equipment of the Husqvarna 333R-Series is another critical feature that sets it apart. It comes with a unique twin line cutting system that uses a high-capacity trimmer head, enabling swift and precise cutting. The ability to quickly swap between trimming heads, including blades for heavier brush, adds versatility to the tool, catering to varying job requirements.

Husqvarna has also integrated advanced anti-vibration technology into the 333R-Series, which minimizes hand and arm strain during operation. This feature enhances overall user comfort, allowing operators to work longer while reducing the risk of fatigue-related injuries.

Moreover, the 333R-Series boasts a tool-less air filter access, simplifying maintenance and increasing uptime. With a robust build and reliable technology, users can trust that this brushcutter will withstand demanding conditions and deliver consistent performance over time.

In summary, the Husqvarna 333R-Series is a powerful, efficient, and ergonomically designed brushcutter that meets the challenges faced by landscaping professionals and avid garden enthusiasts. Its blend of performance, comfort, and ease of maintenance makes it a preferred choice for anyone looking to maintain their outdoor spaces effectively.
Top Page Image Contents