Husqvarna 326RJ manual MANUFACTURER′S Warranty Coverage

Page 26

FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Jonsered are pleased to explain the emissions control system’s warranty on your 2007 and later small off-road engine. In U.S. and Canada, new equipment that use small off-road engines must be designed, built, and equipped to meet the applicable Federal or Californian stringent anti- smog standards. Jonsered must warrant the emissions control system on your small off-road engine for the period listed below provided there has been no abuse, neglect or improper maintenance of your equipment. Your emissions control system may include parts such as the carburetor, ignition system, catalytic converter, fuel tank, filters and other associated components. Also, included may be hoses, belts, connectors, sensors, and other emission-related assemblies. Where a warrantable condition exists, Jonsered will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER′S WARRANTY

COVERAGE

The emissions control system is warranted for two years. If any emissions-related part on your equipment is defective, the part will be repaired or replaced by Jonsered.

OWNER′S WARRANTY RESPONSIBILITIES

•As the small off-road engine owner, you are responsible for performance of the required maintenance listed in your operator’s manual. Jonsered recommends that you retain all receipts covering maintenance on your small off-road engine, but Jonsered cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance.

•As the small off-road engine owner, you should however be aware that Jonsered may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, or improper maintenance or unapproved modifications.

•You are responsible for presenting your small off-road engine to a Jonsered distribution center or service center as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty coverage, you should contact Jonsered, at Sweden +46-36-146500.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.

LENGTH OF COVERAGE

Jonsered warrants to the ultimate purchaser and each subsequent owner that the engine or equipment is designed, built, and equipped so as to conform with all applicable regulations adopted by EPA and CARB, and is free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part under the warranty must be performed at no charge to the owner at a warranty station. Warranty services or repairs will be provided at all Jonsered distribution centers that are franchised to service the subject engines. Throughout the emissions warranty period of two years, Jonsered must maintain a supply of warranted parts sufficient to meet the expected demand for such parts.

WARRANTY PERIOD Any warranted part that is scheduled for replacement as required in the maintenance schedule, is warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part will be repaired or replaced by Jonsered at no cost. Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first scheduled replacement point for the part. Any warranted part that is not scheduled for replacement as required in the maintenance schedule, is warranted for two years. If any such part fails during the period of warranty coverage, it will be repaired and replaced by Jonsered at no cost. Any such part repaired or replaced under the warranty is warranted for the remaining warranty period. Any warranted part that is scheduled only for regular inspection in the maintenance schedule will be warranted for a period of two years. A statement in such written instructions to the effect of ”repair or replace as necessary” will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.

DIAGNOSIS The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station.

CONSEQUENTIAL DAMAGES Jonsered is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part.

EMISSION WARRANTY PARTS LIST

1Carburetor and internal parts

2Intake pipe, airfilter holder and carburetor bolts.

3Airfilter and fuelfilter covered up to maintenance schedule.

4Spark Plug, covered up to maintenance schedule

5Ignition Module

6Muffler with catalytic converter

7Fuel tank

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD -ON OR MODIFIED PARTS

Add-on or modified parts that are not exempted by CARB or EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Jonsered will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 326RJX-series KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what on the trimmer?General Safety Precautions Personal protective equipmentThrottle lockout Machine′s safety equipmentStop switch Muffler Cutting attachment guardVibration damping system Cutting equipment Cutting equipmentLocking nut Sharpening grass cutters and grass blades Trimmer headAssembling the cutting equipment AssemblyFitting the J-handle Fitting other guards and cutting attachments Fuel Fuel safetyFuel Handling Fueling MixingStarting and stopping Starting and StoppingCheck before starting StartingStopping General working instructions Basic safety rulesWorking Techniques Basic working techniquesGrass clearing using a grass blade Grass trimming with a trimmer headSweeping Maintenance CarburetorHigh speed jet H Correctly adjusted carburetorMuffler Spark plug Cleaning the air filterCooling system Air filterBevel gear Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataMANUFACTURER′S Warranty Coverage Federal and California Emissions Control Warranty Statement Super Auto Page Trimmy H Click Trimmy Hit Pro S35 ´z+RN¶5,¨ T35, T35x 1150465-95 ´z+RN¶5,¨ ´z+RN¶5,¨

326RJ specifications

The Husqvarna 326RJ is an innovative addition to the line of string trimmers that caters to both residential and commercial users looking for efficiency and power. Designed with a focus on ergonomic handling and versatility, the 326RJ allows users to tackle various landscaping tasks with ease.

One of the standout features of the Husqvarna 326RJ is its lightweight design, weighing in at just under 10 pounds. This makes it easy to maneuver in tight spaces and reduces fatigue during extended use. The trimmer is powered by a robust 25cc two-stroke engine, which delivers reliable performance and a strong power-to-weight ratio, ensuring that it can handle tough grass and weeds without compromising speed.

Equipped with an efficient X-Torq engine, the Husqvarna 326RJ significantly reduces fuel consumption and minimizes harmful exhaust emissions. This technology not only makes it an environmentally friendly option but also means longer operating times between fuel refills. Users can expect optimal performance while minimizing their carbon footprint.

The ergonomics of the 326RJ are enhanced by the adjustable handle and comfortable grip, allowing for a customizable fit that suits various body types and working conditions. The anti-vibration technology further enhances user comfort by reducing the amount of vibration transmitted to the operator's hands, making long jobs significantly less taxing.

In terms of versatility, the Husqvarna 326RJ is designed to be compatible with a range of optional attachments. This compatibility allows it to not only function as a string trimmer but also perform tasks such as edging and brush cutting, making it a multi-functional tool for landscapers and homeowners alike.

The trimmer features a semi-automatic feed system, which ensures that the trimming line is fed out automatically when tapped on the ground. This keeps the workflow uninterrupted and allows users to focus more on their landscaping tasks without the need to frequently stop to adjust the line.

Overall, the Husqvarna 326RJ combines power, efficiency, and user comfort with a suite of advanced technologies that make it a valuable tool for anyone looking to maintain their lawn or garden. With its blend of features and innovative design, it remains a popular choice among both professionals and DIY enthusiasts.
Top Page Image Contents