Husqvarna 325L, 322L Fitting the spray guard and trimmer head 322C, Fit the appropriate guard

Page 13

ASSEMBLY

Assembling the spray guard and trimmer head Superauto II (322L, 325L-X/L-XT)

Assembling other guards and cutting equipment (322L, 325L-X/L-XT)

• Fit the appropriate

Fit the appropriate guard

(A)for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt

Fit the drive disc (B) on the output axle.

Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing.

Insert the locking pin (C) in the hole so that the axle is locked.

The trimmer head must be split to be fitted (see the diagram). Proceed as follows:

Insert your finger into the centre hole of the cover (I) at the same time as you hold the cover with your other fingers. Press the two catches (J) that extend from the cut-out on the bottom section (K) using the thumb and index finger of your other hand. Press apart the trimmer head using the fingers on the cover.

Place the cover (I) and the support flange (F) on the output axle.

Fit the nut (G). The tightening torque of the nut is 35-50 Nm (3,5-5 kpm). Use the socket spanner in the tool kit. Hold the handle of the spanner as close to the trimmer guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread).

Fit the trimmer head‘s bottom section (K) on the cover (I) by pressing the two sections together with the cut-outs on the bottom section aligned with the catches on the cover.

To dismantle follow the instructions in the reverse order.

 

K

 

J

 

I

 

K

G

 

F

B

I

C

 

 

A

 

guard (A) for use with

 

the trimmer head. Hook

 

the guard onto the shaft

 

fitting and secure it with

 

the bolt (L).

Fit the disc drive (B) on

 

the output axle.

Turn the blade axle until

 

one of the disc drive’s

 

holes aligns with the

 

corresponding hole in

 

the gear housing.

Insert the locking pin

 

(C) into the hole to lock

 

the axle.

Screw on the trimmer

 

head (H) in the

 

direction of rotation.

Dismantling takes place

 

in the reverse order.

Fitting the spray guard and trimmer head (322C)

Guard

• Fit the guard as shown in the diagram. Tighten securely.

Trimmer head

Fit the dust cup on the

shaft. The nut must be completely covered by the dust cup.

Hold the dust cup with a spanner to prevent the shaft from rotating.

• Screw the trimmer head onto the shaft.

English – 13

Image 13
Contents 101 91 322C325L 322L325C 325L325CSymbols Symbol ExplanationMax 10000 rpm Contents Machine‘s safety equipment Safety InstructionsPersonal protective equipment Muffler Vibration damping systemCutting Equipment Locking nutMaintenance Trimmer head Cutting equipmentFuel safety General safety instructionsStart Transport and storageGrass trimming using the trimmer head and plastic knifes Basic safety precautionsGeneral working instructions Basic working techniquesTrimming ClearingSweeping What is what on the trimmer? What is WHAT?Assembly of the trimmer head AssemblyAssembling the loop handlebar 322C, 325CX Assembling the loop handlebar 322L, 325L-X/L-XTFit the appropriate guard Fitting the spray guard and trimmer head 322CFitting the spray guard and trimmer head 325CX Fuel mixture Fuel HandlingFuelling Control before starting Start and StopStart and stop Carburetor MaintenanceCorrectly adjusted carburetor Final setting of the idling speed THigh speed needle Spark plug Muffler Cooling systemTwo-part shaft Air filter Maintenance scheduleAngle gear 322L, 325L-X/L-XT Technical data 322C 322L 325L-X/L-XT Technical DataType Cutting attachment guard Art No Technical data 325CXYour Warranty Rights Obligations Emission Control Warranty StatementSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 12 cm Trimmy SII 502 26 Trimmy ´*313¶5r¨ Page 2001W15