Husqvarna 325RJX-Series manual Start and Stop, Control before starting, Start and stop

Page 17

START AND STOP

Control before starting

For reasons of safety follow these recommendations!

• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

• Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked.

•Ensure the locking nut has

not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

•

Check that the guard is

 

not damaged or cracked.

 

Replace the guard if it is

 

exposed to impact or is

 

cracked.

•

Check that the trimmer

 

head and spray guard are

Cold engine

IGNITION:

Set the stop switch to the start position.

CHOKE:

Set the choke control in the choke position.

AIR PURGE: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.

Warm engine

Use the same starting procedure as for the cold engine, but do not set the choke control in the choke position. The start throttle position is obtained by setting the choke control in the choke position and then returning it to its original position.

Stop

The engine is stopped by switching off the ignition.

!WARNING!

When the engine is started with the choke in the choke or start position the cutting equipment starts to rotate immediately.

not damaged or cracked.

Replace the trimmer head

or spray guard if they are

exposed to impact or are

cracked.

• Never use the machine

without a guard or spray

guard nor with a defective

guard.

Start and stop

!WARNING!

The complete clutch cover with shaft must be fitted before the machine is started, otherwise the clutch can become loose and cause personal injury.

Always move the machine from the filling area before starting. Place the machine on a flat surface. Ensure the cutting equipment cannot come into contact with any object. Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Start

Press the machine body against the ground using your left hand (NOTE! Not your foot). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Reset the choke control as soon as the engine fires and repeat until the engine starts. When the engine starts quickly apply full throttle and the start throttle will automatically disengage. NOTE! Do not pull the starter cord out completely and do not release the starter cord from the fully extended position. This can damage the machine.

English – 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 101 91 325RJMax 10000 rpm Symbol ExplanationSymbols Contents Machine‘s safety equipment Safety InstructionsStop switch Personal protective equipmentVibration damping system Cutting attachment guardLocking nut MufflerCutting equipment Maintenance Safety Instructions Trimmer head Cutting equipmentFiling the grass blade Fuel safety General safety instructionsStart Transport and storageBrush cutting using a grass blade Basic safety precautionsGeneral working instructions Basic working techniquesClearing Grass trimming using the trimmer head and plastic knifesTrimming SweepingWhat is what on the trimmer? What is WHAT?Assembly of the blade and trimmer head AssemblyAssembling the J-handle Assembling the spray guard and trimmer head SuperautoDismantling takes place in the reverse order Fuelling Fuel HandlingFuel mixture Start and stop Start and StopControl before starting Carburettor MaintenanceHigh speed needle H Correctly adjusted carburettor Final setting of the idling speed TSpark plug Muffler Cooling systemDaily maintenance Maintenance scheduleAir filter Angle gearMonthly maintenance Weekly maintenanceTechnical data 325RJ-X Technical DataCutting attachment guard Art No Approved accessories TypeSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 2,4 mm 080-.095 12 cm ~ 3,5 m Trimmy SII 502 26 ´*31@¶6E¨ English 2001W17

325RJX-Series specifications

The Husqvarna 325RJX-Series is designed for professionals and homeowners looking for a reliable and efficient tool for cutting grass, trimming hedges, and maintaining lawns. This series stands out due to its combination of power, maneuverability, and innovative features that cater to a variety of landscaping needs.

One of the primary characteristics of the 325RJX-Series is its robust engine, which delivers impressive performance while maintaining fuel efficiency. The series is equipped with a powerful 25cc two-stroke engine that ensures a reliable power supply, enabling users to tackle tough tasks without compromising on speed or effectiveness. The engine also utilizes Husqvarna’s advanced air injection technology, which helps to minimize air filtration clogging and extend the life of the engine.

The lightweight design of the 325RJX-Series further enhances its usability, making it easier for users to handle and transport. The ergonomic handle provides a comfortable grip, which is particularly beneficial during long periods of operation. Additionally, the balanced design reduces user fatigue, allowing for extended use without discomfort.

Another notable feature is the innovative Auto Return Stop Switch, which simplifies the starting process. After powering down the machine, the switch automatically resets to the "on" position, ensuring quick and effortless restarts when it's time to get back to work. This feature is especially useful for professional landscapers who need to maximize efficiency throughout the day.

The 325RJX-Series also boasts detachable and interchangeable cutting heads, allowing users to switch between a trimmer head and a blade with ease. This versatility makes it suitable for a variety of tasks, from trimming grass around flower beds to cutting through thick brush.

Additionally, this series incorporates vibration dampening technology, which minimizes fatigue by reducing the amount of vibration experienced by the user. This focus on user comfort and operational efficiency has made the 325RJX-Series popular among both professionals and home users.

In summary, the Husqvarna 325RJX-Series is a powerful, lightweight, and versatile trimming solution. With its advanced engine technology, ergonomic design, and innovative features, it is a top choice for anyone seeking to maintain their outdoor spaces effectively and efficiently. Whether for professional use or home landscaping, the 325RJX-Series delivers reliability and performance that users can depend on.
Top Page Image Contents