Husqvarna 323C manual Assembly

Page 13

ASSEMBLY

Fitting a trimmer guard and Superauto II trimmer head (323L, 325Lx, 325LDx)

K

G

 

F

B

 

I

J

C

I

 

 

 

K

 

 

 

A

•Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L).

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows:

•Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half

(K). Pull apart the trimmer head, grasping the cover firmly.

•Place the cover (I) and the support flange (F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible.

To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (left-hand thread).

•Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

•To dismantle, follow the instructions in the reverse order.

Fitting other guards and cutting attachments (323L, 325Lx, 325LDx)

•Fit the correct trimmer guard (A) for use with the trimmer head.

Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L).

A

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

•To dismantle, follow the instructions in the reverse order.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 323C 325CX 323L 325LX 325LDX Symbols KEY to SymbolsContents Machine′s safety equipment Safety InstructionsPersonal protective equipment Muffler Vibration damping systemCutting equipment Locking nutNever use a machine that has a faulty muffler General rules Cutting equipment General safety precautionsTrimmer head StartingBasic safety rules Fuel safetyGeneral working instructions Transport and storageBasic working techniques Grass trimming using a trimmer head and plastic bladesWhat is what? What is WHAT?Fitting the loop handle 323C, 325Cx AssemblyAssembling and dismantling the two-piece shaft 325LDx Fitting the trimmer headAssembly Fitting the trimmer guard and trimmer head 325Cx Fitting the trimmer guard and trimmer head 323CGuard Fuel Fuel HandlingGasoline Two-stroke oilFuelling Check before starting Starting and StoppingStarting and stopping Cold engineStopping Warm engineCarburettor MaintenanceCorrectly adjusted carburettor Fine adjustment of the idle speed TMuffler High speed jet HCooling system Cleaning the air filterSpark plug Two-piece shaftMaintenance schedule Technical data Technical DataTechnical data 325Lx 325LDx Engine Attachments Art No Use with Your Warranty Rights and Obligations Federal Emission Control Warranty StatementSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro S35 25 m T35 Trimmy Page ´z+H43¶5.¨ Page 1140201-95
Top Page Image Contents