Husqvarna 323E, 325E manual Start and Stop, Control before starting, Start and stop

Page 15

START AND STOP

Control before starting

For reasons of safety follow these recommendations!

•Check that the support flange is not cracked due to fatigue

or due to being tightened too much. Replace the support flange if it is cracked.

•Ensure that the nut has not

lost its tightening capacity The nut lock shall have a locking torque of at least 1.5Nm. The nut‘s tightening torque shall be 35-50 Nm.

•Check that the blade and the blade guard are not damaged

or cracked. Replace the blade or blade guard if it has been exposed to impact or if it is cracked.

Cold engine

IGNITION:

Set the stop switch to the start position.

CHOKE:

Set the choke control in the choke position.

AIR PURGE:

Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The dia- phragm need not be com- pletely filled.

Warm engine

Use the same starting proce- dure as for the cold engine, but do not set the choke control in the choke position. The start throttle position is obtained by setting the choke control in the choke position and then returning it to its original position.

Stop

The engine is stopped by switching off the ignition.

!WARNING!

When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately.

Start and stop

!WARNING!

The complete clutch cover with shaft must be fitted before the machine is started, otherwise the clutch can become loose and cause personal injury.

Always move the machine from the filling position before starting. Place the machine on a flat surface. Make sure the blade cannot come into contact with any object. Make sure that no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Start

Press the machine body against the ground using your left hand (NOTE! Not your foot). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Reset the choke control as soon as the engine fires and repeat until the engine starts. When the engine starts quickly apply full throttle and the start throttle will automatically disengage.

NOTE! Do not pull the starter cord out completely and do not release the starter cord from the fully extended position. This can damage the machine.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 323E 325EX-series Symbols Explanation of SymbolsContents Safety Instructions Machine’s safety equipmentPersonal protective equipment Locking nut Vibration damping systemMuffler Cutting equipmentSafety Instructions Safety Instructions Personal protection General safety instructionsSafety instructions regarding the surroundings Safety instructions before starting workFuel safety StartTransport and storage Basic working techniques Basic safety precautionsSafety instructions while working General working instructionsSafety instructions after completing work What is what on the edger? What is WHAT?Assembly Assembling the bladeAssembling the angle gear Fuel Handling Fuel mixtureFuelling Start and Stop Control before startingStart and stop Carburetor MaintenanceHigh speed needle H Correctly adjusted carburetor Final setting of the idling speed TSpark plug Muffler with catalytic converter Cooling systemAngle gear Adjusting the edger‘s cutting depthAir filter Lubricating the flexible drive axleMonthly maintenance Maintenance scheduleDaily maintenance Weekly maintenanceTechnical data 323E Technical DataYour Warranty Rights Obligations Emission Control Warranty StatementEnglish 2001W51 114 00

323E, 325E specifications

The Husqvarna 323E and 325E models represent a significant advancement in the world of outdoor power equipment, specifically designed for pruning and trimming tasks. These lightweight and versatile brush saws are engineered for both professional landscapers and avid gardeners, offering a perfect blend of power, efficiency, and user-friendly design.

One of the main features of the Husqvarna 323E is its low weight, which makes it easy to handle and maneuver during extended use. Weighing in at just over 5 kg (12 lbs), it reduces user fatigue, allowing for long hours of operation without strain. Similarly, the 325E boasts a slightly higher power output while still remaining lightweight, striking an optimal balance between mobility and performance.

Both models are equipped with Husqvarna's innovative X-Torq engine technology, which provides increased power output while reducing fuel consumption and harmful emissions. This makes the 323E and 325E not only efficient machines but also environmentally friendly options for users who prioritize sustainability. The X-Torq engine delivers high torque over a wide RPM range, giving users the ability to tackle tough tasks with ease.

The ergonomic design of these models makes them comfortable to use for extended periods. They feature adjustable handlebars and an anti-vibration system that minimizes fatigue, allowing users to maintain a steady grip and control. The easy-to-use controls further enhance the user experience, enabling operators to focus on the task at hand without unnecessary distractions.

In terms of versatility, the Husqvarna 323E and 325E are compatible with a range of attachments, making them suitable for various applications, from tree care to light brush clearing. This adaptability ensures that users can utilize these tools for a multitude of tasks, maximizing their investment.

In summary, the Husqvarna 323E and 325E brush saws combine lightweight construction with powerful performance and advanced technology. Features like the X-Torq engine, ergonomic design, and versatility make them ideal choices for professionals and enthusiasts alike. With these models, Husqvarna continues to deliver reliable and efficient outdoor equipment tailored to meet the diverse needs of users.
Top Page Image Contents