Husqvarna 322R manual Start and Stop, Control before starting, Start and stop

Page 22

START AND STOP

Control before starting

For reasons of safety follow these recommendations!

•Check the blade to ensure that no cracks have formed at the bottom of the teeth

or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found.

•Check that the support flange is not cracked due to

fatigue or due to being tightened too much. Discard the support flange if it is cracked.

• Ensure the locking nut has

not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm.

•Check that the guard is not damaged or cracked. Replace the guard if it is exposed to impact or is cracked.

•Check that the trimmer head and spray guard are not damaged or cracked. Replace the trimmer head or spray guard if they are exposed to impact or are cracked.

•Never use the machine without a guard or spray guard nor with a defective guard.

Start and stop

!WARNING!

The complete clutch cover with shaft must be fitted before the machine is started, otherwise the clutch can become loose and cause personal injury.

Always move the machine from the filling area before starting. Place the machine on a flat surface. Ensure the cutting equipment cannot come into contact with any object. Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Cold engine

IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position.

AIR PURGE: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.

Warm engine

Use the same starting procedure as for the cold engine, but do not set the choke control in the choke position. The start throttle position is obtained by setting the choke control in the choke position and then returning it to its original position.

Stop

The engine is stopped by switching off the ignition.

!WARNING!

When the engine is started with the choke in the choke or start position the cutting equipment starts to rotate immediately.

Start

Press the machine body against the ground using your left hand (NOTE! Not your foot). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.

Reset the choke control as soon as the engine fires and repeat until the engine starts. When the engine starts quickly apply full throttle and the start throttle will automatically disengage.

NOTE! Do not pull the starter cord out completely and do not release the starter cord from the fully extended position. This can damage the machine.

22 – English

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 322R 325R-X/R-XT 101 91 72Symbol Explanation SymbolsContents Personal protective equipment Safety InstructionsMachine‘s safety equipment Throttle trigger lockAnti-vibration system Stop switchCutting attachment guard Quick-releaseLocking nut MufflerCutting equipment Clearing blades are intended for cutting woodThrottle trigger lock Vibration damping system Cutting equipment Grass blade Cutting equipmentSharpening Trimmer headStart General safety instructionsFuel safety Transport and storageBasic safety precautions General working instructionsBasic clearing techniques Adjusting the harness and clearing sawDesignations Clearing‘s ABC Grass clearing using a grass bladeBrush cutting using the saw blade Working methodsTrimming Grass clearing using the trimmer head and plastic bladesClearing SweepingWhat is WHAT? What is what on the brushcutter?Assembling the handlebars 325R-X/ R-XT AssemblyAssembling the handlebars 322R Transport position, handlebars 325R-X/R-XTGuard. See Technical Data Grass bladeFit the appropriate guard Assembling Adjusting the harness and clearing sawAssembling and dismantling the two-part shaft 325R-XT DismantlingFuel mixture Fuel HandlingFuelling Control before starting Start and StopStart and stop Maintenance CarburetorCorrectly adjusted carburetor Final setting of the idling speed THigh speed needle Angle gear MufflerCooling system Two-part shaftFiling the grass blade Air filter Spark plugOiling the air filter Weekly maintenance Maintenance scheduleDaily maintenance Monthly maintenanceTechnical Data Technical data 322R 325R-XCentre hole in blades Ø 25,4 mm Approved accessories 325R-X/R-XT Type Cutting attachmentType Cutting attachment Guard Art No Guard Ref NoEmission Control Warranty Statement Your Warranty Rights ObligationsSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 2,4 mm 080-.095 12 cm ~ 3,5 m ~ 15 cm ´*31=¶53¨ 502 26 2001W16

322R specifications

The Husqvarna 322R is a versatile and efficient brushcutter designed for extensive use in both residential and professional applications. This powerful piece of equipment is known for its reliable performance, ergonomic design, and cutting-edge features that make yard maintenance tasks more manageable.

One of the standout features of the Husqvarna 322R is its robust 2-stroke engine, which delivers ample power while ensuring fuel efficiency. The engine is engineered to provide consistent performance, allowing users to tackle tough overgrowth with ease. The model comes with an impressive displacement, which translates to enhanced torque and cutting power, enabling operators to handle a variety of tasks ranging from trimming grass to clearing dense vegetation.

The design and ergonomics of the 322R are engineered with the user in mind. It features an adjustable handle that enhances comfort during prolonged use, minimizing fatigue and allowing for greater precision in operating angles. Additionally, it has a lightweight construction that makes it easy to maneuver without sacrificing durability. The harness system is also ergonomically designed to evenly distribute weight, providing optimal balance for the user.

In terms of technology, the 322R incorporates advanced features such as Smart Start™, which enables the engine to start with minimal effort. This innovative technology reduces the resistance in the starter cord, making it easier for users to start the equipment even after extended periods of inactivity. The trimmer is also equipped with an auto-return stop switch, which ensures that the switch automatically resets to the "on" position, allowing for more convenient starting and eliminating unnecessary downtime.

The Husqvarna 322R features a heavy-duty cutting head designed for durability and efficiency. The double-line cutting system delivers a clean and efficient cut, making it suitable for tackling thicker grass and weeds without bogging down. This brushcutter can accommodate various types of cutting attachments, expanding its versatility for different applications.

In addition to its powerful performance and advanced features, the Husqvarna 322R is built with a commitment to sustainability. The engine meets strict emission standards, reducing its environmental impact while delivering high performance.

In summary, the Husqvarna 322R is an exceptional brushcutter that combines power, ergonomic design, and advanced technology. It’s an ideal tool for homeowners and professionals alike, delivering outstanding results for all types of cutting tasks while ensuring comfort and ease of use. Whether clearing brush or maintaining a tidy lawn, the 322R excels in performance and reliability.
Top Page Image Contents