Fueling Engine, HOW to Stop Your Unit

WARNING: Be sure to read the fuel information in the safety rules before you be- gin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an authorized service dealer.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality 2-cycle air- cooled engine oil mixed at a ratio of 40:1 (2.5%). A 40:1 ratio is obtained by mixing 5 liters of unleaded gasoline with 0,125 liter of oil. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on oil container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor- age. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before stor- age for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

HOW TO STOP YOUR UNIT

S To stop the engine, move the ON/OFF switch to the OFF position.

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

Starter Handle

Choke

Lever

Primer Bulb Muffler

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move choke lever to FULL CHOKE posi- tion.

5.Squeeze and hold trigger through all re- maining steps.

6.Pull starter rope handle sharply until en- gine sounds as if it is trying to start, but do not pull rope more than 6 times.

7.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE.

8.Pull starter rope sharply until engine runs, but no more than 6 pulls. If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. NOTE: If engine still doesn’t start, it is probably flooded. Pro- ceed to STARTING A FLOODED EN- GINE.

9.Once the engine starts, allow it to run 10 seconds, then move the choke lever to OFF CHOKE. Allow the unit to run for 30 more seconds at OFF CHOKE before re- leasing the throttle trigger. NOTE: If en- gine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Move the choke lever to the HALF CHOKE position.

3.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

4.Pull starter rope sharply until engine runs, but no more than 5 pulls.

5.Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position.

24C specifications

The Husqvarna 24C is a robust and versatile string trimmer designed for both professionals and homeowners. Known for its performance and reliability, this tool is particularly popular among landscape maintenance professionals who require a durable and efficient solution for trimming grass and weeds in a variety of environments.

One of the standout features of the Husqvarna 24C is its powerful 27cc engine. This two-stroke engine combines high efficiency with low emissions, meeting strict environmental standards without compromising on performance. The engine's design provides strong torque, allowing for effective cutting through thick grass and weeds with ease. Additionally, the Easy Start technology minimizes pull force for starting, making it user-friendly.

The 24C is equipped with a patented, efficient T35 bump feed head. This feature allows users to reload cutting line quickly and easily, minimizing downtime involved with line replacement. With a cutting width of 18 inches, the trimmer provides a wide swath for improved efficiency, making it suitable for large lawns and commercial properties.

Comfort and ergonomics are prioritized in the design of the Husqvarna 24C. The trimmer features adjustable handles that can be tailored to the user’s height, reducing fatigue during prolonged use. The lightweight construction of the tool further enhances maneuverability, allowing users to operate in tight spaces without straining.

Another notable characteristic is the anti-vibration system integrated into the handle and engine. This technology significantly reduces vibrations during operation, ensuring less discomfort for the user over extended periods. This is particularly beneficial for professional landscapers who rely on these tools for daily use.

The 24C also features a protective guard that shields the operator from debris and other hazards. This safety feature, along with durable construction materials, ensures that the trimmer can withstand the rigors of tough landscaping tasks.

In summary, the Husqvarna 24C is a top-tier string trimmer that offers a blend of power, efficiency, and user comfort. Its advanced technologies, including the Easy Start system and anti-vibration capabilities, along with its robust design, make it a preferred choice for those seeking reliability and performance in their lawn care arsenal. Whether you are a homeowner or a landscaping professional, the 24C is built to meet your trimming needs effectively.