Ryobi CS30 RY30120, BC30 RY30160 manual Troubleshooting, Speed. See Figure, Idle Speed Screw

Page 22

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

Engine will not start

1. No spark.

2. No fuel.

3. Engine is flooded.

1.Check spark. Remove spark plug. Reattach the spark plug cap and lay spark plug on metal cylinder. Pull the rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug.

2.Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system is blocked. Contact a service dealer. If primer bulb fills, engine may be flooded, proceed to next item.

3.Set the start lever to the START position. Squeeze the trigger and pull the rope repeatedly until the engine starts and runs.

NOTE: Depending on the severity of the flooding, this may require numerous pulls of the rope. See

Figure 23.

Engine does not reach full speed and emits excessive smoke

1.Incorrect oil/fuel mixture.

2.Air filter is dirty.

3.Spark arrestor screen is dirty.

4.Spark plug fouled.

1.Use fresh fuel and the correct 2-cycle oil mix. (50:1).

2.Clean air filter. Refer to “Replacing and Cleaning Air Filter” earlier in this manual.

3.Contact a servicing dealer.

4.Clean or replace spark plug. Reset spark plug gap. Refer to “Spark Plug Replacement” earlier in this manual.

Engine starts, runs, and ac-

1.

Idle speed screw on carburetor

1.

Turn idle speed screw clockwise to increase idle

 

needs adjustment.

celerates but will not idle

 

 

speed. See Figure 31.

 

 

 

 

 

 

 

 

 

String will not advance

1. String is welded to itself.

1.

Lubricate string with silicone spray.

 

 

2.

Not enough string on spool.

2.

Install more string. Refer to “String Replacement”

 

 

 

 

 

earlier in this manual.

 

 

3.

String is worn too short.

3.

Pull strings while alternately pressing down on

 

 

 

 

 

and releasing spool retainer.

 

 

4.

String is tangled on spool.

4.

Remove string from spool and rewind. Refer to

 

 

 

 

 

“String Replacement” earlier in this manual.

 

 

5.

Engine speed is too slow.

5.

Advance string at full throttle.

 

 

 

 

 

 

 

IDLE SPEED

SCREW

Fig. 31

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Symbols Symbol Name ExplanationService Features Trigger Lock Primer Starter GripRope FrontAssembly Attaching the Storage Hanger Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head See FigureFront Handle Bolt Wing NUT Clamp Attaching the Front Handle CS30 and SS30Attaching the J Handle BC30 Flat WasherTo Attach the Straight Shaft Grass Deflector SS30 Attaching the Grass DeflectorTo Attach the Curved Shaft Grass Deflector CS30 Attaching the Brushcutter Guard BC30Removing the TRI-ARCBLADE and Brushcutter Guard Attaching the Shoulder Harness BC30Converting from Brushcutter to String Trimmer BC30 Converting from String Trimmer to Brushcutter BC30Operation Installing the TRI-ARCBLADE and Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Fueling and Refueling the Trimmer Operating the TrimmerCutting Tips To Advance the Cutting LineTo Advance the Cutting Line Manually Grass Deflector Line Trimming CUT-OFF BladeTRI-ARCBLADE Operating the BrushcutterBlade Thrust Cutting Technique BladeTo Start a Cold Engine Starting and StoppingSee Figures 21 To Stop the EngineSpool Replacement MaintenanceGeneral Maintenance See Figures 24Arrows on Spool Anchor Hole String ReplacementSee Figures 26 First String SlotSpark Plug Replacement Cleaning the Exhaust Port and Muffler Spark ArrestorReplacing and Cleaning AIR Filter Fuel CAPSpeed. See Figure TroubleshootingIdle Speed Screw Warranty This Product WAS Manufactured with a Catalyst MufflerLimited Warranty Statement Maintenance Requirements MANUFACTURER’S Warranty CoverageOWNER’S Warranty Responsibilities CoverageService

SS30 RY30140, CS30 RY30120, BC30 RY30160 specifications

The Ryobi SS30 RY30140, CS30 RY30120, and BC30 RY30160 are key members of Ryobi's extensive lineup of outdoor power equipment, designed for versatility and ease of use. These machines are built to tackle various landscaping tasks, making them ideal for both homeowners and professional landscapers.

The SS30 RY30140 is a robust string trimmer that stands out due to its lightweight design and ergonomic handle, allowing for extended use without causing fatigue. It features a powerful 30cc two-stroke engine that delivers reliable performance, ensuring that grass and weeds can be tackled efficiently. With its adjustable cutting head, users can easily switch between different cutting techniques, making it suitable for edging, trimming, and clearing overgrown areas. The dual-line feed ensures a consistent cutting length, providing precise results with every pass.

The CS30 RY30120 chainsaw is designed for those who require a reliable, powerful tool for cutting and pruning tasks. It boasts a 30cc engine that makes it easy to handle, while still providing adequate power for cutting through branches and logs. The chainsaw features a tool-less chain adjustment system, allowing users to quickly and easily adjust the tension of the chain without requiring any additional tools. This convenience enhances user experience and ensures safety by allowing for timely adjustments while working. The anti-vibration technology integrated into the design reduces operator fatigue, making it more comfortable for prolonged use.

The BC30 RY30160 is a versatile brush cutter that combines power and precision for tackling tougher vegetation. It is equipped with a strong 30cc engine and features a pivoting head, enabling users to easily shift between trimming and clearing modes. This versatile functionality allows for efficient navigation through dense brush, making it perfect for clearing trails or managing overgrown areas. The BC30 also features a double strap harness that distributes weight evenly, providing additional comfort and reducing fatigue during extended work sessions.

All three models incorporate Ryobi’s innovative Easy Start technology, allowing for quick and effortless starts with minimal resistance. Ryobi’s commitment to user-friendly design ensures that even first-time users can operate these tools effectively. Additionally, these models are backed by a robust warranty and reputable customer service, further reinforcing Ryobi's dedication to quality and customer satisfaction.

In summary, the Ryobi SS30 RY30140, CS30 RY30120, and BC30 RY30160 offer a perfect blend of power, comfort, and versatility, making them essential tools for any outdoor maintenance task. Their thoughtful engineering and features cater to various user needs, ensuring that lawn care is efficient and enjoyable.
Top Page Image Contents