Extension Cords, Service Safety | Craftsman 172.79957 manual

SAFETY INSTRUCTIONS cont.

EXTENSION CORDS cont.

The label on your tool may include the following symbols.

V			Volts
A			Amps
Hz			Hertz
W			Watts
min			Minutes
	....................................................................		Alternating current
		..................................................................	Direct current
			Direct current
no			No-load speed
	....................................................................		Class II construction, Double Insulated

RPM………………………............................. . .Revolutions per minute

SPM…...........................…………………….....Strokes per minute

OPM………………..........................………..... Orbits per minute

!	Indicates danger, warning or caution.
	It means attention! Your safety is involved.

SERVICE SAFETY

1.If any part of this hedge trimmer is missing or should break, bend, or fail in any way; or should any electrical component fail to perform properly: SHUT OFF the power switch and remove the trimmer plug from the power source and have the missing, damaged or failed parts replaced BEFORE resuming operation.

2.Tool service should be performed at a Sears Parts and Repair Center. Service or maintenance performed by unqualified personnel could result in a risk of injury.

3.When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure

to follow maintenance instructions may create a risk of electric shock or injury.

SAFETY RULES FOR ELECTRIC HEDGE TRIMMERS

1.DANGER; Risk of cut. Keep hands away from blades. Keep both hands on handles when power is connected to hedge trimmer. DO NOT ATTEMPT to remove cut material or hold material to be cut when blades are moving. Make sure the trimmer switch is off, and the trimmer is disconnected from the power supply when clearing jammed material from blades. DO NOT grasp the exposed cutting blades or cutting edges when picking up or holding the hedge trimmer.

2.CAUTION: Blades coast after hedge trimmer is turned off.

3.KNOW your electric trimmer. Read operator’s manual carefully. Learn the applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire or serious injury.

!DANGER: Laceration Hazard. Keep hands away from blades. Handle blades with care. Keep both hands on handles when power is on.

SAFETY INSTRUCTIONS cont.

SAFETY RULES FOR ELECTRIC HEDGE TRIMMERS cont.

4.Know the controls and know how to stop the blade quickly. Your hedge trimmer was designed with safety in mind. Dual Safety Trigger Switches located on the rear handle and the front auxiliary handle help prevent accidental starting. BOTH trigger switches have to be depressed to turn the hedge trimmer On. ONLY one has to be released to turn the trimmer Off.

5.DO NOT use trimmer without adequate lighting. ALWAYS make sure that you can see what you are trimming and edging.

6.Use trimmer ONLY when vegetation is dry.

7.ALWAYS hold the trimmer by both the main handle and the auxiliary handle for greater control and balance. NEVER reach in front of the safety guard. NEVER, for any reason, touch the cutting blades or any moving parts during use.

8.ALWAYS keep the cord behind the trimmer when in use. DO NOT place the cord over the hedge where it can be cut by the blade.

!WARNING: Do not attempt to remove cut material or hold material to be cut when blades are moving. ALWAYS make sure the trimmer switch is OFF and trimmer is UNPLUGGED when clearing jammed material from blades. DO NOT hold the exposed cutting blades or cutting edges when picking up or holding the hedge trimmer.

9.DO NOT carry the trimmer by the cord or pull the cord to disconnect it from the power receptacle. Keep cord away from heat, oil and sharp edges.

10.DO NOT FORCE the trimmer. Do not try to cut more than what the trimmer is designed for. DO NOT force the unit through thick, dense growth. If the blades slow down, reduce your pace. Trimmer will do a better job with less chance of injury when used at the rate for which it is designed.

11.If hedge trimmer starts to vibrate abnormally, CHECK immediately. Excessive vibration can cause injury.

12.DO NOT OVERREACH. Keep proper footing and balance at all times. Be aware of

footing when taking steps while using trimmer. NEVER run when using your hedge trimmer.

13.STAY ALERT. Watch what you are doing. Use common sense. DO NOT operate the trimmer when you are tired.

14.ALWAYS disconnect the trimmer from power source when not in use, or when you are cleaning or servicing it.

15.MAINTAIN the trimmer with care. Follow instructions for lubricating blades. ALWAYS inspect the hedge trimmer cord and if damaged have repaired, and also inspect extension cord before each use and replace if damaged.

16.KEEP the handle dry, clean and free of oil and grease. Use a clean cloth when cleaning. DO NOT use solvents, brake fluids, gasoline, or other petroleum products to clean the trimmer. They can damage plastic parts.

17.KEEP guard in place and in good working order. NEVER operate trimmer without guard in place. Keep hands away from cutting blades.

18.NEVER use the guard as a handle. NEVER hold the hedge trimmer by the guard. Failure to heed this warning can result in serious personal injury.

172.79957 specifications

The Craftsman 172.79957 is a versatile, high-performance tool meticulously designed for both DIY aficionados and professional craftsmen. This tool stands out in its category due to its combination of durability, ergonomic design, and innovative technology.

One of the primary features of the Craftsman 172.79957 is its robust construction. Built with high-quality materials, it guarantees long-lasting performance, making it ideal for heavy-duty applications. The tool's housing is designed to withstand harsh working conditions, ensuring that it remains operational even in demanding environments. This durability is coupled with a well-thought-out ergonomic design that offers a comfortable grip and reduces user fatigue, allowing for longer operating times without discomfort.

The Craftsman 172.79957 also incorporates advanced technology to enhance its functionality. For instance, it features a powerful motor that provides ample torque and speed, making it efficient for various tasks such as cutting, drilling, and fastening. This motor is paired with an intelligent speed control system, allowing users to easily adjust the speed according to the specific requirements of each project. This makes the Craftsman 172.79957 a versatile tool, suitable for numerous applications, from precise tasks to more intensive operations.

Additionally, the tool boasts a range of accessories designed to expand its capabilities. These include various drill bits, saw blades, and other attachments that can easily be swapped out, enabling users to tackle a wide array of jobs without the need for multiple tools. The quick-release chuck system further enhances usability, allowing for fast and easy changes of accessories.

Safety is another highlight of the Craftsman 172.79957. It is equipped with built-in safety features such as an electric brake that stops the tool instantly, minimizing the risk of accidents. Moreover, the tool's design includes protective guards and finger grips that ensure a secure hold, adding an extra layer of safety during operation.

In summary, the Craftsman 172.79957 is a powerful and reliable tool that combines rugged construction, ergonomic design, and innovative technologies. Whether you are a seasoned professional or a hobbyist, this tool is designed to provide the performance and versatility needed to complete a variety of tasks efficiently and safely. Its robust features, coupled with a focus on user comfort and safety, make it an excellent addition to any tool collection.