Snapper LT180H33IBV, LT180H38IBV, ELT145H33HBV Battery Testing, NEW Battery Preparation

Page 30

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT OVERFILL! DO NOT attempt to service or charge the battery while it is installed on the machine. DO NOT use “BOOST” chargers on the battery.

4.5.5.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The Battery Condition chart shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

4.5.6NEW BATTERY PREPARATION

1.Remove battery from carton.

2.Place battery in a well ventilated area on a level non- concrete surface.

3.Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4.5.7. BATTERY TESTING

4.With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16” above cell plates is the recommended level. DO NOT place anything in battery other than specified electrolyte.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16” above cell plates.

7.Reinstall cell caps.

8.Slide battery partially into battery housing.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

10.Insert battery completely into battery housing.

11.Reinstall seat assembly.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal. BLACK (Negative) cable must go to the ( - ) terminal.

Battery Condition Chart

 

State of Charge

Syringe Hydrometer

Digital Voltmeter

Five Ball Hydrometer

100%

Charged w/ Sulfate Stop

1.280

12.80v

Five Balls Floating

100%

Charged

1.265

12.60v

Four Balls Floating

75% Charged

1.210

12.40v

Three Balls Floating

50% Charged

1.160

12.10v

Two Balls Floating

25% Charged

1.120

11.90v

One Ball Floating

0% Charged

Less than 1.100

Less than 11.80v

Zero Balls Floating

30

Image 30
Contents European Lawn Tractor Hydrostatic Drive Series H Model Number ExplanationImportant Safety Instructions Operation From PreviousTable of Contents Familiarization Components ControlsFamiliarization Decals / Symbols Lights on Engine OFF Engine on Start PRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStopping ENGINE, BLADE, Wheel Drive Stopping Engine Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping Wheel DriveStopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeService Every 25 Operating Hours Check Engine Check 33 Deck Drive BeltMower Components Tractor Lubrication Annually END of Each Season Fuel FilterAnnually END of Each Season 3.4.2. Fuel Filter Spark Plug Hydrostatic Transmission OILDeck Blade Brake Adjustment Engine Adjustments & RepairBlade Brake Adjustment On nextBlade Belt Adjustment 33 Deck from previous Adjusting Mower Blade 33 Decks OnlySide View of Deck Deck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Front to Rear Front Lift RODTractor Drive Components 4.3.1. Brake Adjustment Steering AdjustmentShifter Adjustment Mower Blade Service Standard Blade Wear Limits Standard Blade Sharpening Mower Blade ReplacementNinja Blade Wear Limits Ninja Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction Drive Belt Replacement Traction drive belt removalMower Deck Removal Traction drive belt replacementTraction drive belt removal from previous View from Underneath TractorDeck Belt Removal & Replacement 33 Deck Drive Belt Traction drive belt replacement from previousDeck Belt Removal & Replacement Deck Drive BeltBattery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Electrical System Electrical System Troubleshooting Guide Uneven tire pressure Bring to proper pressure Ninja Tractor Drive Belts Mower BladesModel No Engine to Transmission Engine to Deck Standard ELT145H33HBVYear Limited Warranty Disclaimer of WarrantyService Notes Service Notes European Lawn Tractor Hydrostatic Drive Series H

LT150H38IBV, WLT145H38HBV, LT150H38HKV, LT180H38IBV, LT180H33IBV specifications

The Snapper ELT145H33HBV, LT150H33IBV, LT145H33HBV, LT145H38HBV, and WLT150H38IBV are a series of high-performance lawn mowers engineered for both residential and commercial applications. These machines are designed to deliver superior cutting performance, ease of use, and durability, making them a preferred choice for landscape professionals and homeowners alike.

One of the standout features of these Snapper models is the powerful engine technology. The ELT145H33HBV features a robust 145cc engine that provides ample power for tackling large lawns with thick grass, while the LT150H33IBV boasts a 150cc engine designed for enhanced torque and cutting efficiency. Both engines are designed for easy starting and low maintenance, allowing users to quickly get to work without worrying about the typical hassles associated with engine upkeep.

These mowers are equipped with a high-performance cutting deck, which varies by model but generally features a wider design for increased cutting capacity. The LT145H33HBV, for instance, offers a precision-engineered deck that ensures an even cut across different terrains. The adjustable cutting height feature allows operators to choose from various settings, accommodating different grass types and personal preferences.

The usability of these models is further enhanced by ergonomic design features, including comfortable grips and easy-to-manage controls. The pull-start system is intuitive, ensuring that even novice users can operate the mowers with confidence. Additionally, many of these models feature foldable handles for improved storage and transport, making them ideal for users with limited space.

In terms of build quality, Snapper is recognized for its rugged construction. The mowers are designed to withstand tough conditions, featuring a robust frame and durable materials that resist wear and tear over time. This durability translates to longer lifespan and reliability, making these models cost-effective choices for long-term use.

Consumers will also benefit from Snapper’s commitment to innovation, incorporating advanced propulsion technologies. These mowers are often equipped with features that provide superior traction and stability, allowing for precise maneuverability even on hilly or uneven terrains.

Overall, the Snapper ELT145H33HBV, LT150H33IBV, LT145H33HBV, LT145H38HBV, and WLT150H38IBV are versatile, efficient, and dependable lawn mowers. With their combination of powerful engines, resilient design, and user-friendly features, these machines are tailored to meet the demands of both professional landscapers and everyday homeowners, ensuring a beautifully manicured lawn with minimal effort.