Snapper LT150H38IBV Tractor Drive Components 4.3.1. Brake Adjustment, Steering Adjustment

Page 23

Section 4 - ADJUSTMENT & REPAIR

4.3TRACTOR DRIVE COMPONENTS 4.3.1. BRAKE ADJUSTMENT

1.To be properly adjusted, the brake should stop the tractor in approximately 6 feet from top speed when the clutch/brake pedal is fully depressed.

2.Adjust brake when necessary as follows:

3.Turn engine “OFF”. Remove key.

4.Locate brake adjustment nut underneath the rear of tractor. See Figure 4.13.

5.Turn nut clockwise to increase braking action or counterclockwise to decrease braking action.

6.Start engine and test brake.

7.Continue adjustment as described above until proper adjustment is achieved.

ROTATE ADJUSTING NUT CLOCKWISE TO

INCREASE BRAKING OR COUNTER

CLOCKWISE TO DECREASE BRAKING

FIGURE 4.13

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.3.2STEERING ADJUSTMENT

Should excessive “Play” be noted in the steering, adjust as follows:

1.Turn engine “OFF”. Remove key.

2.From left side of tractor, locate the steering sector below fuel tank. See Figure 4.14.

FUEL TANK

ROTATE TO

LESSEN “PLAY”

ECCENTRIC MOUNTING NUT

FIGURE 4.14

3.Loosen the eccentric mounting nut and rotate the eccentric clockwise until steering “Play” is reduced. Refer back to Figure 4.14.

4.Tighten eccentric mounting nut.

4.3.3.SHIFTER ADJUSTMENT

The shift linkage is set at the factory and should not require further adjustment. The shifter is adjusted properly when the speed control lever can be placed at rear edge of the neutral detent and the tractor remains absolutely stationary. If motion is detected, neutral adjustment will be required. DO NOT operate a machine that creeps when shifted to neutral.

1.Stop engine. Remove key.

2.Move speed control lever to rear edge of neutral detent and hold firmly.

3.Locate neutral adjustment nut underneath the right rear of the tractor. See Figure 4.15

4.Turn the neutral adjustment nut 1/4 turn clockwise to reduce FORWARD creep. Turn the adjustment nut 1/4 turn counter clockwise to reduce Reverse creep. Only turn the adjustment nut in 1/4 turn increments.

5.Check for creep in neutral. Start engine. Move speed control lever to rear edge of the neutral detent. Machine should not move. If further adjustment is required, stop engine and repeat Step 4.

WARNING

DO NOT adjust shift linkage with engine running. The adjustment requires hands to be close to rotating parts. STOP engine. REMOVE key.

(Continued on next page)

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model Number Explanation European Lawn Tractor Hydrostatic Drive Series HImportant Safety Instructions From Previous OperationTable of Contents Components Controls FamiliarizationFamiliarization Decals / Symbols Lights on Engine OFF Engine on Start OPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStopping Wheel Drive Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping ENGINE, BLADE, Wheel Drive Stopping EngineReleasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismCheck Blade Brake Service After First 5 HoursIntroduction Change Engine OILMower Components Service Every 25 Operating Hours Check EngineCheck 33 Deck Drive Belt Tractor Lubrication Fuel Filter Annually END of Each SeasonSpark Plug Hydrostatic Transmission OIL Annually END of Each Season 3.4.2. Fuel FilterOn next Engine Adjustments & RepairBlade Brake Adjustment Deck Blade Brake AdjustmentAdjusting Mower Blade 33 Decks Only Blade Belt Adjustment 33 Deck from previousSide View of Deck Deck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Front Lift ROD Deck Level Adjustment Front to Rear Sector PlatesShifter Adjustment Tractor Drive Components 4.3.1. Brake AdjustmentSteering Adjustment Mower Blade Service Standard Blade Wear Limits Ninja Blade Sharpening Mower Blade ReplacementNinja Blade Wear Limits Standard Blade SharpeningTraction drive belt removal Mower Blade ReplacementTraction Drive Belt Replacement Traction Drive Belt Replacement Mower Deck RemovalView from Underneath Tractor Traction drive belt replacementTraction drive belt removal from previous Mower Deck RemovalDeck Drive Belt Traction drive belt replacement from previousDeck Belt Removal & Replacement Deck Belt Removal & Replacement 33 Deck Drive BeltBattery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable Accessories Electrical System Electrical System Troubleshooting Guide Uneven tire pressure Bring to proper pressure ELT145H33HBV Tractor Drive Belts Mower BladesModel No Engine to Transmission Engine to Deck Standard NinjaDisclaimer of Warranty Year Limited WarrantyService Notes Service Notes European Lawn Tractor Hydrostatic Drive Series H

LT150H38IBV, WLT145H38HBV, LT150H38HKV, LT180H38IBV, LT180H33IBV specifications

The Snapper ELT145H33HBV, LT150H33IBV, LT145H33HBV, LT145H38HBV, and WLT150H38IBV are a series of high-performance lawn mowers engineered for both residential and commercial applications. These machines are designed to deliver superior cutting performance, ease of use, and durability, making them a preferred choice for landscape professionals and homeowners alike.

One of the standout features of these Snapper models is the powerful engine technology. The ELT145H33HBV features a robust 145cc engine that provides ample power for tackling large lawns with thick grass, while the LT150H33IBV boasts a 150cc engine designed for enhanced torque and cutting efficiency. Both engines are designed for easy starting and low maintenance, allowing users to quickly get to work without worrying about the typical hassles associated with engine upkeep.

These mowers are equipped with a high-performance cutting deck, which varies by model but generally features a wider design for increased cutting capacity. The LT145H33HBV, for instance, offers a precision-engineered deck that ensures an even cut across different terrains. The adjustable cutting height feature allows operators to choose from various settings, accommodating different grass types and personal preferences.

The usability of these models is further enhanced by ergonomic design features, including comfortable grips and easy-to-manage controls. The pull-start system is intuitive, ensuring that even novice users can operate the mowers with confidence. Additionally, many of these models feature foldable handles for improved storage and transport, making them ideal for users with limited space.

In terms of build quality, Snapper is recognized for its rugged construction. The mowers are designed to withstand tough conditions, featuring a robust frame and durable materials that resist wear and tear over time. This durability translates to longer lifespan and reliability, making these models cost-effective choices for long-term use.

Consumers will also benefit from Snapper’s commitment to innovation, incorporating advanced propulsion technologies. These mowers are often equipped with features that provide superior traction and stability, allowing for precise maneuverability even on hilly or uneven terrains.

Overall, the Snapper ELT145H33HBV, LT150H33IBV, LT145H33HBV, LT145H38HBV, and WLT150H38IBV are versatile, efficient, and dependable lawn mowers. With their combination of powerful engines, resilient design, and user-friendly features, these machines are tailored to meet the demands of both professional landscapers and everyday homeowners, ensuring a beautifully manicured lawn with minimal effort.
Top Page Image Contents