Snapper LT180H42IBV2, LT200H42IBV2, LT200H48IBV2 Introduction, Service After First 5 Hours

Page 13

Section 3 – MAINTENANCE

3.1 INTRODUCTION

To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, always mention the model and serial number. SNAPPER recommends returning the Tractor to an authorized SNAPPER dealer annually for inspection and addition of any new devices, which might upgrade the safety of the Tractor. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer’s dealers under the heading, ENGINES - gasoline.

3.2 SERVICE - AFTER FIRST 5 HOURS

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

3.2.1. CHANGE ENGINE OIL

The engine is equipped with a Fastex™ oil drain.

1.Rotate drain body counterclockwise and pull out to open drain. See Figure 3.1.

2.Drain oil into a 2 quart container placed beneath end of oil drain.

3.After all oil has drained, push drain body "IN" and rotate clockwise to close.

4.Fill engine with new motor oil as specified in engine owner's manual.

WARNING

The following procedure requires the engine and blades to be operated. Exercise extreme caution. Clear area of loose parts & tools first. Only operate blades when seated in the operator’s seat.

3.2.2. CHECK BLADE BRAKE

1.Check blade brake for proper function. Blades should stop rotating in 5 seconds or less after pushing the blade switch “IN” to the OFF disengaged position.

2.If blades continue to rotate longer than 5 seconds do not operate machine. Contact your SNAPPER dealer for assistance.

3.2.3. CHECK MOWER BLADES

1.Remove deck from tractor.

2.Carefully position deck to access blade.

3.Check blade for sharpness, wear and damage. Refer to Section “BLADE WEAR LIMITS”.

4.Check blade for straightness. Refer to Section

“ADJUSTING MOWER BLADE”.

5.Check torque of blade mounting bolts. Torque to: 42" deck - 30 to 40 ft lbs. See Figure 3.2.

48" deck - 70 to 80 ft lbs.

OIL

FILLER

TUBE

FASTEX™

OIL DRAIN

ROTATE COUNTER-

CLOCKWISE AND PULL

OUT TO OPEN.

PUSH IN AND ROTATE

CLOCKWISE TO CLOSE.

FIGURE 3.1

TORQUE TO

30 TO 40 FT.LBS.

42” DECK

SHOWN

FIGURE 3.2

WARNING

Blades must stop rotating in 5 seconds or less after blades have been turned off. DO NOT operate machine until blade brake has been repaired and functioning properly. Contact your SNAPPER dealer for assistance.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Engine Option Engine Type Engine Model Series Designation 180From Previous Column Important Safety InstructionsSafe Handling of Gasoline Towing Table of Contents Components Controls FamiliarizationOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistSee Figure Starting & Operation Starting EngineStarting Wheel Drive Starting & OperationStopping ENGINE, BLADE, Wheel Drive 2.4.1. Stopping Engine Starting Mower BladeCutting Height Adjustment Setting Park BrakeStopping Stopping Mower Blades Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismIntroduction Service After First 5 HoursChange Engine OIL Check Blade BrakeCheck Deck Drive Belt Service Every 25 Operating Hours 3.3.1. Check EngineEngine Cooling System Engine Must not Start if Air Filter Single Cylinder EngineEngine should Start if Engine Must Begin to Stop ifTractor Lubrication Mower ComponentsFuel Filter Annually END of Each SeasonSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairBlade Belt Adjustment Mower Deck Adjustment Levelness 1. SIDE-To-SIDE 42 DecksMower Deck Adjustment Levelness FRONT-To-REAR 42 Decks TOP View of Deck Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksOn Next Front To Rear Mower Deck Adjustment LevelnessSteering Adjustment Tractor Drive Components Brake AdjustmentShifter Adjustment Mower Blade Service Standard Blade Wear Limits Standard Blade Sharpening Ninja Blade Wear LimitsNinja Blade Sharpening Traction Drive Belt Replacement 42 Mower Deck Removal 5 & 48 Mower Blade ReplacementDeck Shown View from Underneath Tractor Traction drive belt replacementMower Deck Removal Traction Drive Belt ReplacementEngine Loosen Tension Idler Pulley Nuts Tension Idler Spring Remove Spring from TOP View Mower Deck Battery Installation Battery Battery RemovalBattery Charging Battery StorageBattery Condition Chart State of Charge Digital Voltmeter Battery TestingNEW Battery Preparation Available LT160H42IBV AccessoriesLT200H48IBV2 LT180H42IBV2Electrical B & S Twin Cylinder Engine Electrical B & S Single Cylinder Engine Corrective Action Problem Probable CauseBad battery cells Blade belt requires adjustmentMaintenance Parts Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Service Notes Service Notes Service Notes Lawn Tractor Hydrostatic Drive Electric Clutch Series

LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV2, LT200H48IBV2 specifications

The Snapper LT series of lawn tractors, including models LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV, and LT200H48IBV2, are designed to provide exceptional performance and user-friendly features for residential lawn care. Each model combines advanced technology with robust build quality, yielding reliable performance for homeowners looking to maintain their lawns with ease.

A key feature across the LT series is the powerful engine options. These tractors are equipped with premium engines that deliver impressive horsepower, ensuring a smooth cutting experience even in dense or tough grass conditions. Additionally, the innovative design offers a hydrostatic transmission, enabling seamless speed adjustments without the need for manual shifting. This promotes a more comfortable and controlled mowing experience.

The cutting decks of the Snapper LT models are another highlight, with options ranging from 42 inches to 48 inches for efficient grass cutting. This range allows users to choose the deck size that best suits their lawn size and complexity. The cutting height can be easily adjusted, providing versatility for maintaining the perfect lawn, whether it requires a close trim or a more elevated cut.

Another noteworthy characteristic of the Snapper LT series is the ergonomic seating and controls. The high-back seat is adjustable, providing comfort during extended mowing sessions, while the user-friendly dashboard keeps essential controls within easy reach. This design focus supports an overall better user experience, reducing fatigue during operation.

Safety is paramount in the design of the LT models. Features such as the automatic shut-off when the operator leaves the seat and robust construction contribute to a safer mowing environment.

Durability is also a hallmark of the Snapper LT series. The rugged chassis and durable materials used in the construction mean these tractors can withstand the rigors of regular use, ensuring long-term reliability and value.

Overall, the Snapper LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV, and LT200H48IBV2 offer an excellent combination of power, comfort, and versatility for homeowners. Their innovative features and robust performance position them as excellent choices for anyone looking to enhance their lawn care experience while achieving professional-looking results.
Top Page Image Contents