Snapper LT180H42IBV2, LT200H42IBV2, LT200H48IBV2 5 & 48 Mower Blade Replacement, Deck Shown

Page 25

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.4.5.42" & 48” MOWER BLADE REPLACEMENT

1.Move tractor to a firm, level surface.

2.Turn engine "OFF". Remove key.

3.Remove mowing deck from tractor.

4.Position deck on its left side to access blade.

5.Remove blade mounting bolts on 42” decks or nuts on 48” decks. See Figure 4.17.

6.Install new blade.

7.Torque 30 to 40 ft lbs. for 42” Deck. Torque 80 to 90 ft lbs. for 48” Deck.

SPINDLE

BLADE

ASSEMBLY

BAR

BLADE

 

 

CONE

 

WASHER

BLADE MOUNTING

42” SPINDLE BOLT ASSEMBLY SHOWN

FIGURE 4.17

4.4.7.TRACTION DRIVE BELT REPLACEMENT 42” Mower Deck Removal

It is necessary to remove deck in order to replace belts. Remove deck as follows:

1.Place tractor on a firm, level surface such as a driveway or garage floor and set the park brake.

2.Turn engine “OFF”. Remove key.

3.Lower the deck to lowest setting.

4.Remove hair pin and washer securing front lift cable to front lift arm. See Figure 4.18.

5.Remove hair pins from the front deck hanger rod and slide out the rod from deck hanger bracket. Front lift arms will be now be disconnected. See Figure 4.19.

6.Hold front of deck "UP" and slide the front deck hanger rod to the right and out then lower the front of deck to the ground.

7.Remove deck drive belt from engine pulley bottom groove. See Figure 4.20.

HAIR PIN

CLEVIS

PIN

 

WASHER

JAM NUT

FRONT LIFT CABLE

42” DECK SHOWN

FIGURE 4.18

RIGHT

SIDE

SHOWN

DECK HANGER

BRACKET

FRONT

AXLE

FRONT DECK

HANGER ROD

FRONT

HAIR PIN

LIFT ARM

 

FIGURE 4.19

ELECTRIC

CLUTCH

REMOVE BELT

FROM PULLEY

FIGURE 4.20

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Engine Option Engine Type Engine Model Series Designation 180From Previous Column Important Safety InstructionsSafe Handling of Gasoline Towing Table of Contents Components Controls FamiliarizationOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistSee Figure Starting & Operation Starting EngineStarting Wheel Drive Starting & OperationStopping ENGINE, BLADE, Wheel Drive 2.4.1. Stopping Engine Starting Mower BladeCutting Height Adjustment Setting Park BrakeStopping Stopping Mower Blades Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismIntroduction Service After First 5 HoursChange Engine OIL Check Blade BrakeCheck Deck Drive Belt Service Every 25 Operating Hours 3.3.1. Check EngineEngine Cooling System Engine Must not Start if Air Filter Single Cylinder EngineEngine should Start if Engine Must Begin to Stop ifTractor Lubrication Mower ComponentsFuel Filter Annually END of Each SeasonSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairBlade Belt Adjustment Mower Deck Adjustment Levelness 1. SIDE-To-SIDE 42 DecksMower Deck Adjustment Levelness FRONT-To-REAR 42 Decks TOP View of Deck Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksOn Next Front To Rear Mower Deck Adjustment LevelnessSteering Adjustment Tractor Drive Components Brake AdjustmentShifter Adjustment Mower Blade Service Standard Blade Wear Limits Standard Blade Sharpening Ninja Blade Wear LimitsNinja Blade Sharpening Traction Drive Belt Replacement 42 Mower Deck Removal 5 & 48 Mower Blade ReplacementDeck Shown View from Underneath Tractor Traction drive belt replacementMower Deck Removal Traction Drive Belt ReplacementEngine Loosen Tension Idler Pulley Nuts Tension Idler Spring Remove Spring from TOP View Mower Deck Battery Installation Battery Battery RemovalBattery Charging Battery StorageBattery Condition Chart State of Charge Digital Voltmeter Battery TestingNEW Battery Preparation Available LT160H42IBV AccessoriesLT200H48IBV2 LT180H42IBV2Electrical B & S Twin Cylinder Engine Electrical B & S Single Cylinder Engine Corrective Action Problem Probable CauseBad battery cells Blade belt requires adjustmentMaintenance Parts Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Service Notes Service Notes Service Notes Lawn Tractor Hydrostatic Drive Electric Clutch Series

LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV2, LT200H48IBV2 specifications

The Snapper LT series of lawn tractors, including models LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV, and LT200H48IBV2, are designed to provide exceptional performance and user-friendly features for residential lawn care. Each model combines advanced technology with robust build quality, yielding reliable performance for homeowners looking to maintain their lawns with ease.

A key feature across the LT series is the powerful engine options. These tractors are equipped with premium engines that deliver impressive horsepower, ensuring a smooth cutting experience even in dense or tough grass conditions. Additionally, the innovative design offers a hydrostatic transmission, enabling seamless speed adjustments without the need for manual shifting. This promotes a more comfortable and controlled mowing experience.

The cutting decks of the Snapper LT models are another highlight, with options ranging from 42 inches to 48 inches for efficient grass cutting. This range allows users to choose the deck size that best suits their lawn size and complexity. The cutting height can be easily adjusted, providing versatility for maintaining the perfect lawn, whether it requires a close trim or a more elevated cut.

Another noteworthy characteristic of the Snapper LT series is the ergonomic seating and controls. The high-back seat is adjustable, providing comfort during extended mowing sessions, while the user-friendly dashboard keeps essential controls within easy reach. This design focus supports an overall better user experience, reducing fatigue during operation.

Safety is paramount in the design of the LT models. Features such as the automatic shut-off when the operator leaves the seat and robust construction contribute to a safer mowing environment.

Durability is also a hallmark of the Snapper LT series. The rugged chassis and durable materials used in the construction mean these tractors can withstand the rigors of regular use, ensuring long-term reliability and value.

Overall, the Snapper LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV, and LT200H48IBV2 offer an excellent combination of power, comfort, and versatility for homeowners. Their innovative features and robust performance position them as excellent choices for anyone looking to enhance their lawn care experience while achieving professional-looking results.
Top Page Image Contents