Snapper LT180H42IBV, LT200H42IBV2, LT200H48IBV2 Starting & Operation Starting Engine, See Figure

Page 8

Section 2 - OPERATING INSTRUCTIONS

2.3STARTING & OPERATION

2.3.1.STARTING ENGINE

1.Take a comfortable position in seat of machine, look around to make sure that the area you are going to mow is clear of people, children and pets. Take note of any stationary obstacles!

NOTE: The interlock system will prevent the engine from starting if the blade switch is in the "ON" (up) position or if the clutch/brake pedal is not fully depressed. If the interlock system ever fails to work, DO NOT OPERATE the tractor until the interlock has been repaired.

2.Push blade switch down to the "OFF" position.

See Figure 2.4.

PUSH BLADE SWITCH “DOWN” TO

 

START MACHINE

BLADE

SWITCH

5.Choke engine for cold starting by moving engine speed control to "CHOKE" position. NOTE: Some models are equipped with a separate choke control, located on the dash of the tractor. Pull the control “OUT” to choke position to start a cold engine. Little or no choking will be needed when restarting a warm engine. Insert key in switch. Turn key to "START" position to crank engine and hold until engine starts, then release key to “RUN” position. See Figure 2.6.

NOTE: DO NOT crank engine for more than five seconds at a time. This will help prevent the starter from overheating and/or running down the battery. If cranking time is more than five seconds, locate and correct cause of starting problem.

6.After engine starts, release key, move the engine speed control to "FAST" position and allow engine to warm up before proceeding. See Figure 2.6.

OFF

FIGURE 2.4

3.Depress the clutch/brake pedal fully. See Figure 2.5.

4.Move speed control lever to neutral.

NOTE: The seat interlock will shut off the engine if the operator gets off the seat without setting the parking brake or if the blades are running. If the interlock ever fails to work, DO NOT OPERATE the tractor until the interlock has been repaired.

CLUTCH/BRAKE

PEDAL

PARK

BRAKE

LEVER

DOWN

PUSH PEDAL ALL THE

WAY DOWN TO START

ENGINE

FIGURE 2.5

CHOKE LIGHT POSITION SWITCH

FAST

SLOW

ENGINE

SPEEDKEY CONTROL

FIGURE 2.6

WARNING

DO NOT leave machine with engine running. Stop engine. Stop blades. Set parking brake. Remove key.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 180 Engine Option Engine Type Engine Model Series DesignationImportant Safety Instructions From Previous ColumnSafe Handling of Gasoline Towing Table of Contents Familiarization Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine See FigureStarting & Operation Starting Wheel DriveStopping ENGINE, BLADE, Wheel Drive 2.4.1. Stopping Engine Starting Mower BladeSetting Park Brake Cutting Height AdjustmentStopping Stopping Mower Blades Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours IntroductionChange Engine OIL Check Blade BrakeEngine Cooling System Service Every 25 Operating Hours 3.3.1. Check EngineCheck Deck Drive Belt Air Filter Single Cylinder Engine Engine Must not Start ifEngine should Start if Engine Must Begin to Stop ifMower Components Tractor LubricationSpark Plug Hydrostatic Transmission OIL Annually END of Each SeasonFuel Filter Engine Adjustments & Repair Blade Brake AdjustmentBlade Belt Adjustment Mower Deck Adjustment Levelness 1. SIDE-To-SIDE 42 DecksMower Deck Adjustment Levelness FRONT-To-REAR 42 Decks On Next Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksTOP View of Deck Mower Deck Adjustment Levelness Front To RearShifter Adjustment Tractor Drive Components Brake AdjustmentSteering Adjustment Mower Blade Service Standard Blade Wear Limits Ninja Blade Sharpening Ninja Blade Wear LimitsStandard Blade Sharpening Deck Shown 5 & 48 Mower Blade ReplacementTraction Drive Belt Replacement 42 Mower Deck Removal Traction drive belt replacement View from Underneath TractorTraction Drive Belt Replacement Mower Deck RemovalEngine Loosen Tension Idler Pulley Nuts Tension Idler Spring Remove Spring from TOP View Mower Deck Battery Battery Removal Battery InstallationBattery Charging Battery StorageNEW Battery Preparation Battery TestingBattery Condition Chart State of Charge Digital Voltmeter Accessories Available LT160H42IBVLT200H48IBV2 LT180H42IBV2Electrical B & S Twin Cylinder Engine Electrical B & S Single Cylinder Engine Problem Probable Cause Corrective ActionBlade belt requires adjustment Bad battery cellsMaintenance Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Service Notes Service Notes Service Notes Lawn Tractor Hydrostatic Drive Electric Clutch Series

LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV2, LT200H48IBV2 specifications

The Snapper LT series of lawn tractors, including models LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV, and LT200H48IBV2, are designed to provide exceptional performance and user-friendly features for residential lawn care. Each model combines advanced technology with robust build quality, yielding reliable performance for homeowners looking to maintain their lawns with ease.

A key feature across the LT series is the powerful engine options. These tractors are equipped with premium engines that deliver impressive horsepower, ensuring a smooth cutting experience even in dense or tough grass conditions. Additionally, the innovative design offers a hydrostatic transmission, enabling seamless speed adjustments without the need for manual shifting. This promotes a more comfortable and controlled mowing experience.

The cutting decks of the Snapper LT models are another highlight, with options ranging from 42 inches to 48 inches for efficient grass cutting. This range allows users to choose the deck size that best suits their lawn size and complexity. The cutting height can be easily adjusted, providing versatility for maintaining the perfect lawn, whether it requires a close trim or a more elevated cut.

Another noteworthy characteristic of the Snapper LT series is the ergonomic seating and controls. The high-back seat is adjustable, providing comfort during extended mowing sessions, while the user-friendly dashboard keeps essential controls within easy reach. This design focus supports an overall better user experience, reducing fatigue during operation.

Safety is paramount in the design of the LT models. Features such as the automatic shut-off when the operator leaves the seat and robust construction contribute to a safer mowing environment.

Durability is also a hallmark of the Snapper LT series. The rugged chassis and durable materials used in the construction mean these tractors can withstand the rigors of regular use, ensuring long-term reliability and value.

Overall, the Snapper LT180H42IBV2, LT200H42IBV2, LT200H48IBV2, LT180H42IBV, LT200H42IBV, and LT200H48IBV2 offer an excellent combination of power, comfort, and versatility for homeowners. Their innovative features and robust performance position them as excellent choices for anyone looking to enhance their lawn care experience while achieving professional-looking results.
Top Page Image Contents