Snapper LT2044 manual Valve, Open, Closed

Page 26

Regular Maintenance

Oil Drain Valve Operation

1.Place a suitable container with a 4 quart capacity under the oil drain valve (A, Figure 22 or 23).

2.Loosen or remove the dip stick (C, Figure 22 or 23).

3.Wipe oil drain valve (B, Figure 24) and cover (C) with paper towel or rag.

NOTE: Sliding a hose with a 1/2” (12.5 mm) inside diameter tube over the valve nipple may aid in guiding the draining oil.

4.Rotate the drain valve (B) counter clockwise and pull out 1/4” (6.35 mm) for engine oil to drain. Allow ample time for complete drainage.

5.After all the oil has drained, close the oil drain valve

(B) by pushing in and rotating clockwise to close.

6.Wipe the nipple (D) with paper towel or rag. Install the cover (C) over nipple (D).

A

 

A

 

 

 

B

B

 

 

 

 

D

Valve

 

Valve

 

Open

Closed

C

C

 

 

Figure 24. Oil Drain Valve

A.Engine Block / Valve Base

B.Oil Drain Valve

C.Cover

D.Nipple

Change Engine Oil

BRIGGS & STRATTON MODELS

Service Interval: 50 hours or once per season.

Oil Capacity: Approximately1-7/8 quarts (1.8L) without filter change.

NOTE: Change engine oil while the engine is warm. Run the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 22 or 23) and oil drain valve (A).

2.Drain engine oil. See OIL DRAIN VALVE OPERATION above.

3.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL.

Change Engine Oil & Filter

BRIGGS & STRATTON MODELS

Service Interval: 100 hours or once per season.

Oil Capacity: Approximately 2 quarts (1.9L) with oil filter change.

NOTE: Change engine oil while the engine is warm. Run the engine for a few minutes, then shut the engine off and allow it to cool from hot to warm.

1.Clean the area around the dip stick (C, Figure 22 or 23) and oil drain valve (A).

2.Drain engine oil. See OIL DRAIN VALVE OPERATION above.

3.Remove the oil filter (B). Discard the filter.

4.Using a drop of oil on your finger tip, wet the rubber gasket on the bottom of the new filter.

Use oil classified API Service Class SF, SG, SH, SJ or better with SAE Viscosity:

 

 

 

 

 

 

30 Conventional**

 

 

 

 

5W-30

 

 

 

 

 

 

 

10W-30

 

 

 

 

 

 

Conventional*

 

 

 

 

 

 

Synthetic 5W-30, 10W-30

 

 

˚F

-20

0

20

32

40

60

80

100

˚C

-30

-18

-7

0

4

16

27

38

*CAUTION: Air cooled engines run hotter than automotive engines. The use of non-synthetic multi-viscosity oils (5W-30, 10W-30, etc.) in temperatures above 40º F (4ºC) will result in higher than normal oil consumption. When using a multi-viscosity oil, check oil level more frequently.

**CAUTION: SAE 30 oil, if used below 40º F (4ºC), will result in hard starting and possible engine bore damage due to inadequate lubrication.

Figure 25. Recommended Engine Oil -

Briggs & Stratton Models

5.Turn the filter clockwise until the rubber gasket meets the filter base. Then turn 1/2 to 3/4 turn more.

6.Fill the crankcase with oil. See CHECK ENGINE OIL LEVEL.

7.Test run the engine to check for leaks. Stop the engine for 1 minute, then recheck the oil level.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 1734103 18.5HP Hydro Tractors Mower Decks20HP Hydro Tractors Mower Decks Page Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service & Maintenance Safe Handling of GasolineTractor ID Tag Mower ID Tag Identification NumbersCE Identification Tag Markings Safety Icons Safety DecalsSafety Decals CE Safety Icons Decals LocationsChoke Control FunctionsThrottle Control HeadlightsFeatures & Controls Cruise Control Operation Volt Power OutletParking Brake Function HourmeterAdding Fuel General Operating SafetyOperational Safety Checks Starting The EngineOperating the Tractor Removing the Mower Deck Mower Deck Removal & InstallationInstalling the Mower Deck Muffler and surrounding areas may be hotStorage Adjusting Mower Cutting HeightAttaching a Trailer Before Every Spring Each Hours 100 Fall Use Check Tire PressuresBefore Every Spring Each Hours 100 250 Fall Use SizePTO Clutch Adjustment Check Regular MaintenanceSafety Interlock System Check Engine Maintenance Battery MaintenanceK46 Maintenance Transmission MaintenanceHood Removal and Installation Transmission IdentificationOil Service Interval Every 25 HoursLubrication GreaseService Interval Yearly Lubricate Rear Axle ShaftsService Interval Every 100 Hours or As Required Servicing the Mower BladesCheck & Fill Engine Oil Closed ValveOpen Air Filter Service Air Filter Removal & InstallationPre-Cleaner Service Air FilterBriggs & Stratton Single Cylinder Models Replace Spark Plug Troubleshooting Adjustment, & Service TroubleshootingTroubleshooting the Mower Battery Charging Troubleshooting, Adjustment, & ServiceSeat Adjustment Brake AdjustmentPTO clutch adjustment Adjust PTO Clutch Window Adjustment Nut Feeler GaugeGauge Wheels Select Models Fuse ReplacementMower Adjustments Leveling The Mower 1/2 Max High cutMower Belt Replacement To avoid damaging belts, do not PRYLT Series 20 HP* Briggs & Stratton18.5 HP* Briggs & Stratton K46Technical Manuals Replacement PartsMaintenance Items Page Lawn Care Lawn Care & Mowing Information

LT2044 specifications

The Snapper LT2044 is a versatile and robust lawn tractor designed for homeowners who prioritize efficiency and comfort in their lawn care routine. With its powerful engine and innovative features, the LT2044 is capable of handling a variety of mowing tasks, making it a go-to choice for lawn enthusiasts.

At the heart of the LT2044 is a reliable 20 horsepower engine, which provides ample power to tackle larger lawns and tackle tough grass with ease. The engine features an automatic choke system, ensuring smooth starts in any weather condition. With a hydrostatic transmission, operators can enjoy seamless speed control without the need for gear shifting. This advanced transmission system allows for effortless maneuverability, especially in tight spaces and around obstacles such as trees or garden beds.

One of the standout features of the Snapper LT2044 is its 44-inch cutting deck. This deck is made from durable materials, ensuring longevity and consistent performance over time. The cutting height can be easily adjusted from 1.5 to 4 inches, giving users the flexibility to achieve their desired lawn finish. Additionally, the deck is equipped with a mulching capability, allowing homeowners to finely chop grass clippings that can then nourish the lawn, reducing waste and the need for bagging.

Comfort is another key aspect of the LT2044. It features an ergonomic seat and steering wheel, designed to reduce strain during longer mowing sessions. The tractor also includes easy-to-use controls, allowing users to operate the machine effortlessly. Its compact design enhances maneuverability, making it easier to navigate through narrow paths and corners.

For added convenience, the Snapper LT2044 comes with a 12-volt battery for easy starting and operates quietly, making it ideal for residential areas where noise can be a concern. The tractor is also compatible with various attachments, such as baggers and mulchers, further enhancing its versatility.

In summary, the Snapper LT2044 lawn tractor combines power, efficiency, and comfort, making it an excellent choice for those seeking a reliable machine for lawn maintenance. With its numerous features and technologies, this tractor is well-equipped to handle a range of yard sizes and challenges, providing homeowners with a dependable solution for all their lawn care needs.
Top Page Image Contents