Snapper HZS18483BVE, HZS15423KVE Battery Battery Removal, Battery Service, Battery Storage

Page 20

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. Never attempt to service or charge the battery while it is installed on the YARD CRUISER. Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position as shown. If battery is removed, DO NOT operate engine without insulating Positive + battery cable terminal with electrical tape, or sparking from the battery cables can result.

4.4BATTERY

4.4.1. BATTERY REMOVAL

1.Tilt seat up to gain access to battery.

2.Observe and note cable positions on battery. See Figure 4.14.

3.Disconnect cables from battery terminals, disconnecting BLACK (Negative) cable first. Disconnect RED (Positive) battery cable. Slide battery from battery cradle.

4.Retain mounting bolts and nuts for future use.

4.4.2.BATTERY INSTALLATION 1. Slide battery into battery cradle.

2. Connect cables to battery terminals. Connect RED (Positive) cable first. Connect BLACK (Negative) cable. See Figure 4.14.

3. Place the positive (+) terminal insulator over positive terminal and cable. See Figure 4.15.

BLACK

NEGATIVE (-)

CABLE

RED

POSITIVE (+)

CABLE

FIGURE 4.14

WARNING

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda. DO NOT attempt to charge battery while installed on the YARD CRUISER. DO NOT use “BOOST” chargers on the battery.

4.4.3. BATTERY SERVICE

1.Remove battery. See Section on Battery Removal

2.Place battery in a well ventilated area on a level surface.

3.Using distilled water, refill cells as required to cover cell plates. Fluid level in battery can be seen through the cell case.

4.With cell caps removed, connect battery charger to battery terminals. Red to positive (+) terminal and black to negative (-) terminal.

5.Slow charge battery at 1 amp for 10 hours.

6.If battery will not accept charge or is partially charged after 10 hours of charging at 1 amp, replace with new battery, Part Number 6-0753.

4.4.4. BATTERY STORAGE

If YARD CRUISER is to be stored out of season on its rear bumper, it is recommended the battery be removed, charged and stored.

1.Remove battery. (Refer to Section ”BATTERY REMOVAL”).

2.Perform battery service.

3.Bring battery to full charge, if required.

4.Store battery in an area away from the YARD CRUISER on a wood surface. DO NOT STORE BATTERY ON A CONCRETE SURFACE.

4.4.5.NEW BATTERY PREPARATION 1. Remove battery from carton.

2. Place battery in a well ventilated area on a level non-concrete surface.

3. Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4. With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

21

Image 20
Contents Yard Cruiser Important Safety Instructions Operation Table of Contents Left Console View Right Console ViewIntroduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation Engine Electric Start Mower Blade StoppingWheel Drive Parking BrakeCutting Height Adjustment Service After First 5 Hours Change Engine OILCheck Mower Blade Single Blade DeckService Every 25 Operating Hours 3.3.1. Engine Check Mower Drive Belt 1. Footrest RemovalMower Components 5. Mower Blade Spindle Lubrication Service Annually Storage OUT of SeasonEngine Adjustments & Repair Mower Drive Belt AdjustmentBelt Replacement Belt RemovalBlade Brake Hairpin Lift ARM Front or Rear View of Deck Twin Blade Deck Deck ShownWheel Brake Adjustment Blade Sharpening Mower Blade Replacement 4.3.1. Blade Wear LimitsBlade Replacement Battery Storage Battery Battery RemovalBattery Service Battery Condition Chart Battery TestingBearing Replacement 48 Decks Troubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Loss Of TractionService Performed Each USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Yard Cruiser Hydro Drive Series

HZS15423KVE, HZS18483BVE, HZS18483BVE, HZS15423KVE specifications

Snapper has long been a trusted name in outdoor power equipment, and their line of lawn mowers is no exception. Among their impressive offerings are the Snapper HZS18483BVE, HZS15423KVE, and HZS15423KVE models. Each of these mowers is designed to provide exceptional performance, durability, and ease of use, catering to the needs of homeowners and professional landscapers alike.

The Snapper HZS18483BVE is equipped with an 18-inch cutting deck, making it ideal for medium to large lawns. Its powerful, easy-start engine ensures that you can get to work promptly. The mower features a 3-in-1 cutting system, allowing for mulching, bagging, and side discharge capabilities. This versatility provides homeowners with the flexibility to manage grass clippings according to their own preferences.

One of the standout characteristics of the HZS18483BVE is its patented SureCut technology, which enables a superior cutting performance across various grass types and conditions. Additionally, its lightweight design and self-propulsion feature make it easy to maneuver and navigate around obstacles, allowing for a more efficient mowing experience.

The Snapper HZS15423KVE and HZS15423KVE models, while similar, offer their unique features aimed at different mowing needs. Both mowers come with a 21-inch cutting deck, perfect for larger areas, and feature the same reliable engine as the HZS18483BVE. The HZS15423KVE is designed with an adjustable cutting height, and smooth rolling wheels that ensure a clean cut every time.

Furthermore, these mowers feature a user-friendly starting system, making them accessible for users of all experience levels. The durable steel construction guarantees longevity, making them a wise investment for any lawn care enthusiast.

When it comes to maintenance, Snapper’s designs allow for easy access to key components, such as the air filter and spark plug, ensuring routine upkeep is hassle-free. These models are also equipped with high-capacity grass bags, enabling longer mowing sessions without frequent emptying.

In conclusion, the Snapper HZS18483BVE and HZS15423KVE models offer exceptional power, performance, and versatility. Their innovative technologies and robust characteristics set them apart in the crowded lawn mower market, providing users with reliable tools to maintain their lawns efficiently. Whether you have a small garden or an expansive yard, these Snapper mowers deliver cutting-edge solutions for any landscaping challenge.