Snapper ELT150H33IBV Introduction, Service After First 5 Hours, Change Engine OIL

Page 14

Section 3 - MAINTENANCE

3.1 INTRODUCTION

To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, always mention the model and serial number. SNAPPER recommends returning the Tractor to an authorized SNAPPER dealer annually for inspection and addition of any new devices, which might upgrade the safety of the Tractor. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer’s dealers under the heading, ENGINES - gasoline.

3.2 SERVICE - AFTER FIRST 5 HOURS

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

3.2.1. CHANGE ENGINE OIL

These model tractors are equipped Fastex™ oil drains.

1.Rotate drain body counterclockwise and pull out to open drain. See Figure 3.1.

2.Drain oil into a 2 quart container placed beneath end of oil drain.

3.After all oil has drained, push drain body "IN" and rotate clockwise to close.

4.Fill engine with new motor oil as specified in engine owner's manual.

WARNING

The following procedure requires the engine and blades to be operated. Exercise extreme caution. Clear area of loose parts & tools first. Only operate blades when seated in the operator’s seat.

3.2.2. CHECK BLADE BRAKE

1.Check blade brake for proper function. Blades should stop rotating in 5 seconds or less after moving the blade engagement lever down to the OFF position.

2.If blades continue to rotate longer than 5 seconds do not operate machine. Refer to Section “BLADE BRAKE ADJUSTMENT” or contact your SNAPPER dealer for assistance.

3.2.3. CHECK MOWER BLADE

1.Remove deck from tractor.

2.Carefully position deck to access blade.

3.Check blade for sharpness, wear and damage. Refer to Section “BLADE WEAR LIMITS”.

4.Check blade for straightness. Refer to Section

“ADJUSTING MOWER BLADE”.

5.Check torque of blade mounting bolts.

Torque 33" deck to: - 30 to 40 ft lbs. See Figure 3.2.

OIL

FILLER

TUBE

FASTEX™

OIL DRAIN

ROTATE COUNTER-

CLOCKWISE AND PULL OUT

TO OPEN.

PUSH IN AND ROTATE

CLOCKWISE TO CLOSE.

FIGURE 3.1

TORQUE 33” BLADE TO 30 TO 40 FT. LBS.

FIGURE 3.2

WARNING

Blades must stop rotating in 5 seconds or less after blades have been turned off. DO NOT operate machine until blade brake has been repaired and functioning properly. Contact your SNAPPER dealer for assistance.

15

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Explanation 150Preparation Protection for ChildrenProtection Against Tipovers Maintenance OperationTable of Contents Familiarization Components ControlsFamiliarization Decals / Symbols Lights on Engine OFF Engine on Start PRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStopping ENGINE, BLADE, Wheel Drive Stopping Engine Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping Wheel DriveStopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeMower Components Service Every 25 Operating Hours Check EngineCheck 33 Deck Drive Belt Tractor Lubrication Annually END of Each Season Fuel FilterSpark Plug Hydrostatic Transmission OIL Annually END of Each Season 3.4.2. Fuel FilterFrom Previous Deck Blade Brake Adjustment Engine Adjustments & RepairBlade Brake Adjustment On nextBlade Belt Adjustment 33 Deck from previous Adjusting Mower Blade 33 Decks OnlySide View of Deck Deck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Front to Rear Front Lift RODShifter Adjustment Tractor Drive Components 4.3.1. Brake AdjustmentSteering Adjustment Mower Blade Service Standard Blade Wear Limits Standard Blade Sharpening Mower Blade ReplacementNinja Blade Wear Limits Ninja Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction Drive Belt Replacement Traction drive belt removalView from Underneath Tractor Traction drive belt replacementTraction drive belt removal from previous Deck Belt Removal & Replacement 33 Deck Drive Belt Traction drive belt replacement from previousDeck Belt Removal & Replacement Deck Drive BeltBattery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Available ELT150H33IBV AccessoriesElectrical System Schematics Briggs & Stratton with Lights Troubleshooting Guide Problem Probable Cause Corrective ActionUneven tire pressure Bring to proper pressure Ninja Tractor Drive Belts Mower BladesModel No Engine to Transmission Engine to Deck Standard ELT150H33IBVEYear Limited Warranty Disclaimer of WarrantyService Notes Service Notes European Lawn Tractor Hydrostatic Drive Series

ELT150H33IBV specifications

The Snapper ELT150H33IBV is a versatile and powerful lawn mower designed to meet the needs of homeowners and landscape professionals alike. With a robust engine and a range of innovative features, this machine ensures efficient grass cutting and exceptional performance across various terrains.

At the heart of the ELT150H33IBV is its reliable 150cc engine, which delivers ample power for tackling even the toughest grasses. This engine is designed for fuel efficiency, allowing users to mow their lawns without frequent refueling stops. The recoil start system ensures that the mower is easy to start, providing convenience for users of all experience levels.

One of the standout features of the Snapper ELT150H33IBV is its 33-inch cutting deck. This compact size allows for easy maneuvering in tight spaces, making it ideal for residential yards with intricate landscaping. The cutting deck is constructed with durable materials that withstand the rigors of regular use while ensuring a high-quality cut.

The mower offers multiple cutting height adjustments, allowing users to customize the height of their grass according to their preferences or lawn care needs. This feature is particularly useful for maintaining different types of grass and ensuring a healthy lawn throughout the mowing season.

In terms of technology, the Snapper ELT150H33IBV incorporates a unique Blade Brake system, which enhances safety by stopping the blade immediately when the user releases the handlebar. This ensures that users can quickly stop mowing without needing to turn off the engine, reducing the risk of accidents. Additionally, the mower is equipped with a reliable drive system that ensures smooth operation and improved traction on various surfaces.

The Snapper ELT150H33IBV is designed with user comfort in mind, featuring adjustable handles for better ergonomics. This reduces fatigue during prolonged use, allowing for a more enjoyable mowing experience. Furthermore, the mower's compact design facilitates easy storage, making it an excellent choice for homeowners with limited space.

Overall, the Snapper ELT150H33IBV combines power, versatility, and user-friendly features to provide a reliable lawn care solution. Its advanced technology and robust construction make it a standout choice for anyone looking to maintain a pristine lawn effortlessly. Whether you're a seasoned gardener or a first-time mower, the Snapper ELT150H33IBV offers the performance and reliability you need to tackle any lawn care challenge.
Top Page Image Contents