Snapper ELT150H33IBV Tractor Drive Components 4.3.1. Brake Adjustment, Steering Adjustment

Page 23

Section 4 - ADJUSTMENT & REPAIR

4.3TRACTOR DRIVE COMPONENTS 4.3.1. BRAKE ADJUSTMENT

1.To be properly adjusted, the brake should stop the tractor in approximately 6 feet from top speed when the clutch/brake pedal is fully depressed.

2.Adjust brake when necessary as follows:

3.Turn engine “OFF”. Remove key.

4.Locate brake adjustment nut underneath the rear of tractor. See Figure 4.13.

5.Turn nut clockwise to increase braking action or counterclockwise to decrease braking action.

6.Start engine and test brake.

7.Continue adjustment as described above until proper adjustment is achieved.

ROTATE ADJUSTING NUT CLOCKWISE TO

INCREASE BRAKING OR COUNTER

CLOCKWISE TO DECREASE BRAKING

FIGURE 4.13

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.3.2STEERING ADJUSTMENT

Should excessive “Play” be noted in the steering, adjust as follows:

1.Turn engine “OFF”. Remove key.

2.From left side of tractor, locate the steering sector below fuel tank. See Figure 4.14.

FUEL TANK

ROTATE TO

LESSEN “PLAY”

ECCENTRIC MOUNTING NUT

FIGURE 4.14

3.Loosen the eccentric mounting nut and rotate the eccentric clockwise until steering “Play” is reduced. Refer back to Figure 4.14.

4.Tighten eccentric mounting nut.

4.3.3.SHIFTER ADJUSTMENT

The shift linkage is set at the factory and should not require further adjustment. The shifter is adjusted properly when the speed control lever can be placed at rear edge of the neutral detent and the tractor remains absolutely stationary. If motion is detected, neutral adjustment will be required. DO NOT operate a machine that creeps when shifted to neutral.

1.Stop engine. Remove key.

2.Move speed control lever to rear edge of neutral detent and hold firmly.

3.Locate neutral adjustment nut underneath the right rear of the tractor. See Figure 4.15

4.Turn the neutral adjustment nut 1/4 turn clockwise to reduce FORWARD creep. Turn the adjustment nut 1/4 turn counter clockwise to reduce Reverse creep. Only turn the adjustment nut in 1/4 turn increments.

5.Check for creep in neutral. Start engine. Move speed control lever to rear edge of the neutral detent. Machine should not move. If further adjustment is required, stop engine and repeat Step 4.

WARNING

DO NOT adjust shift linkage with engine running. The adjustment requires hands to be close to rotating parts. STOP engine. REMOVE key.

(Continued on next page)

24

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 150 Model Number ExplanationPreparation Protection for ChildrenProtection Against Tipovers Operation MaintenanceTable of Contents Components Controls FamiliarizationFamiliarization Decals / Symbols Lights on Engine OFF Engine on Start OPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStopping Wheel Drive Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping ENGINE, BLADE, Wheel Drive Stopping EngineReleasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismCheck Blade Brake Service After First 5 HoursIntroduction Change Engine OILMower Components Service Every 25 Operating Hours Check EngineCheck 33 Deck Drive Belt Tractor Lubrication Fuel Filter Annually END of Each SeasonSpark Plug Hydrostatic Transmission OIL Annually END of Each Season 3.4.2. Fuel FilterFrom Previous On next Engine Adjustments & RepairBlade Brake Adjustment Deck Blade Brake AdjustmentAdjusting Mower Blade 33 Decks Only Blade Belt Adjustment 33 Deck from previousSide View of Deck Deck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Front Lift ROD Deck Level Adjustment Front to Rear Sector PlatesShifter Adjustment Tractor Drive Components 4.3.1. Brake AdjustmentSteering Adjustment Mower Blade Service Standard Blade Wear Limits Ninja Blade Sharpening Mower Blade ReplacementNinja Blade Wear Limits Standard Blade SharpeningTraction drive belt removal Mower Blade ReplacementTraction Drive Belt Replacement Traction Drive Belt Replacement Mower Deck RemovalView from Underneath Tractor Traction drive belt replacementTraction drive belt removal from previous Deck Drive Belt Traction drive belt replacement from previousDeck Belt Removal & Replacement Deck Belt Removal & Replacement 33 Deck Drive BeltBattery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable ELT150H33IBV Accessories Available AccessoriesElectrical System Schematics Briggs & Stratton with Lights Problem Probable Cause Corrective Action Troubleshooting GuideUneven tire pressure Bring to proper pressure ELT150H33IBVE Tractor Drive Belts Mower BladesModel No Engine to Transmission Engine to Deck Standard NinjaDisclaimer of Warranty Year Limited WarrantyService Notes Service Notes European Lawn Tractor Hydrostatic Drive Series

ELT150H33IBV specifications

The Snapper ELT150H33IBV is a versatile and powerful lawn mower designed to meet the needs of homeowners and landscape professionals alike. With a robust engine and a range of innovative features, this machine ensures efficient grass cutting and exceptional performance across various terrains.

At the heart of the ELT150H33IBV is its reliable 150cc engine, which delivers ample power for tackling even the toughest grasses. This engine is designed for fuel efficiency, allowing users to mow their lawns without frequent refueling stops. The recoil start system ensures that the mower is easy to start, providing convenience for users of all experience levels.

One of the standout features of the Snapper ELT150H33IBV is its 33-inch cutting deck. This compact size allows for easy maneuvering in tight spaces, making it ideal for residential yards with intricate landscaping. The cutting deck is constructed with durable materials that withstand the rigors of regular use while ensuring a high-quality cut.

The mower offers multiple cutting height adjustments, allowing users to customize the height of their grass according to their preferences or lawn care needs. This feature is particularly useful for maintaining different types of grass and ensuring a healthy lawn throughout the mowing season.

In terms of technology, the Snapper ELT150H33IBV incorporates a unique Blade Brake system, which enhances safety by stopping the blade immediately when the user releases the handlebar. This ensures that users can quickly stop mowing without needing to turn off the engine, reducing the risk of accidents. Additionally, the mower is equipped with a reliable drive system that ensures smooth operation and improved traction on various surfaces.

The Snapper ELT150H33IBV is designed with user comfort in mind, featuring adjustable handles for better ergonomics. This reduces fatigue during prolonged use, allowing for a more enjoyable mowing experience. Furthermore, the mower's compact design facilitates easy storage, making it an excellent choice for homeowners with limited space.

Overall, the Snapper ELT150H33IBV combines power, versatility, and user-friendly features to provide a reliable lawn care solution. Its advanced technology and robust construction make it a standout choice for anyone looking to maintain a pristine lawn effortlessly. Whether you're a seasoned gardener or a first-time mower, the Snapper ELT150H33IBV offers the performance and reliability you need to tackle any lawn care challenge.
Top Page Image Contents