Snapper ELT150H33IBV Troubleshooting Guide, Problem Probable Cause Corrective Action

Page 34

TROUBLESHOOTING GUIDE

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

 

Starter Will Not

1. Battery dead.

1.

Service battery.

Crank Engine

 

 

 

 

 

2.

Blown fuse.

2.

Replace fuse.

 

3.

Electrical connections loose or corroded.

3.

Clean and check connections for good contact.

 

4.

Defective ignition switch.

4.

Contact authorized SNAPPER dealer.

 

 

 

 

 

 

5.

Starter Spins without engaging.

5.

Release Start key and repeat attempt. If starter

 

 

 

 

continues to spin contact Engine Dealer.

Engine Will Not

1. Blade engagement switch in the “ON”

1.

Move blade engagement switch to “OFF”.

Start

 

position.

 

 

 

2.

Park brake not set.

2.

Set park brake.

 

3.

Fuel tank empty.

3.

Fill fuel tank with fresh fuel.

 

4.

Engine needs choking.

4.

Move engine speed control to “CHOKE”.

 

5.

Spark plug wire disconnected.

5.

Place spark plug wire onto spark plug.

 

6.

Battery weak or dead.

6.

Service battery.

 

7.

Faulty interlock switch.

7.

Contact authorized SNAPPER dealer.

Engine Stalls After

1. Operator not in seat.

1.

Sit in operator’s seat.

Running

2. Engine speed control in the “CHOKE”

2.

Move engine speed control to “FAST”.

 

 

position.

 

 

 

3.

Fuel tank empty.

3.

Fill with fuel to proper level.

 

4.

Engine air pre-cleaner and or air cleaner

4.

Clean free of all debris.

 

 

dirty.

 

 

 

5.

Spark plug defective or gap set improperly.

5.

Service spark plug.

 

6.

Fuel filter stopped up.

6.

Replace fuel filter.

 

7.

Water, debris or stale fuel in fuel system.

7.

Drain and clean fuel system.

Engine Loses

1. Excessive load on engine.

1.

Lessen load by slowing ground speed.

Power

 

 

 

 

 

2.

Engine air pre-cleaner or air cleaner dirty.

2.

Clean or replace filters.

 

3.

Engine oil level low.

3.

Fill with engine oil to proper level.

 

4.

Engine cooling fins and air screens

4.

Clean free of all debris.

 

 

excessively dirty.

 

 

 

5.

Spark plug faulty.

5.

Service spark plug.

 

6.

Water, debris or stale fuel in fuel system.

6.

Drain and clean fuel system.

Engine Backfires

1. Engine speed control set too “FAST”.

1. Set engine speed control to “SLOW” and allow

When Turned To

 

 

 

engine to idle. Then, turn key to “OFF”.

“STOP”

 

 

 

 

Excessive

1. Damaged or bent mower blades.

1.

Service mower blade(s).

Vibration

 

 

 

 

 

2.

Loose blade components.

2.

Service and tighten loose parts.

 

3.

Loose or missing air lift (if equipped).

3.

Replace air lifts. Tighten to proper torque.

(Continued on next Page)

35

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model Number Explanation 150Protection Against Tipovers Protection for ChildrenPreparation Maintenance OperationTable of Contents Familiarization Components ControlsFamiliarization Decals / Symbols Lights on Engine OFF Engine on Start PRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStopping ENGINE, BLADE, Wheel Drive Stopping Engine Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Stopping Wheel DriveStopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeCheck 33 Deck Drive Belt Service Every 25 Operating Hours Check EngineMower Components Tractor Lubrication Annually END of Each Season Fuel FilterFrom Previous Annually END of Each Season 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Deck Blade Brake Adjustment Engine Adjustments & RepairBlade Brake Adjustment On nextBlade Belt Adjustment 33 Deck from previous Adjusting Mower Blade 33 Decks OnlySide View of Deck Deck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Front to Rear Front Lift RODSteering Adjustment Tractor Drive Components 4.3.1. Brake AdjustmentShifter Adjustment Mower Blade Service Standard Blade Wear Limits Standard Blade Sharpening Mower Blade ReplacementNinja Blade Wear Limits Ninja Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction Drive Belt Replacement Traction drive belt removalTraction drive belt removal from previous Traction drive belt replacementView from Underneath Tractor Deck Belt Removal & Replacement 33 Deck Drive Belt Traction drive belt replacement from previousDeck Belt Removal & Replacement Deck Drive BeltBattery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Available ELT150H33IBV AccessoriesElectrical System Schematics Briggs & Stratton with Lights Troubleshooting Guide Problem Probable Cause Corrective ActionUneven tire pressure Bring to proper pressure Ninja Tractor Drive Belts Mower BladesModel No Engine to Transmission Engine to Deck Standard ELT150H33IBVEYear Limited Warranty Disclaimer of WarrantyService Notes Service Notes European Lawn Tractor Hydrostatic Drive Series

ELT150H33IBV specifications

The Snapper ELT150H33IBV is a versatile and powerful lawn mower designed to meet the needs of homeowners and landscape professionals alike. With a robust engine and a range of innovative features, this machine ensures efficient grass cutting and exceptional performance across various terrains.

At the heart of the ELT150H33IBV is its reliable 150cc engine, which delivers ample power for tackling even the toughest grasses. This engine is designed for fuel efficiency, allowing users to mow their lawns without frequent refueling stops. The recoil start system ensures that the mower is easy to start, providing convenience for users of all experience levels.

One of the standout features of the Snapper ELT150H33IBV is its 33-inch cutting deck. This compact size allows for easy maneuvering in tight spaces, making it ideal for residential yards with intricate landscaping. The cutting deck is constructed with durable materials that withstand the rigors of regular use while ensuring a high-quality cut.

The mower offers multiple cutting height adjustments, allowing users to customize the height of their grass according to their preferences or lawn care needs. This feature is particularly useful for maintaining different types of grass and ensuring a healthy lawn throughout the mowing season.

In terms of technology, the Snapper ELT150H33IBV incorporates a unique Blade Brake system, which enhances safety by stopping the blade immediately when the user releases the handlebar. This ensures that users can quickly stop mowing without needing to turn off the engine, reducing the risk of accidents. Additionally, the mower is equipped with a reliable drive system that ensures smooth operation and improved traction on various surfaces.

The Snapper ELT150H33IBV is designed with user comfort in mind, featuring adjustable handles for better ergonomics. This reduces fatigue during prolonged use, allowing for a more enjoyable mowing experience. Furthermore, the mower's compact design facilitates easy storage, making it an excellent choice for homeowners with limited space.

Overall, the Snapper ELT150H33IBV combines power, versatility, and user-friendly features to provide a reliable lawn care solution. Its advanced technology and robust construction make it a standout choice for anyone looking to maintain a pristine lawn effortlessly. Whether you're a seasoned gardener or a first-time mower, the Snapper ELT150H33IBV offers the performance and reliability you need to tackle any lawn care challenge.
Top Page Image Contents